BOSCH SHE4AEM6N 100 Series Black Full Console Dishwasher
en-usꢀDishwasher Connection
2. If using the Top Mount, and screw the 1/2" (12.7mm)
wood screws through the holes in the mounting
brackets. Choose the bracket hole best suited for your
installation.
effectiveness. Lower water temperatures will increase run
times. The hot water supply pressure must be between 15
- 145 psi (1 - 10 bar).
WARNING
Scalding Hazard
▶ Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
NOTICE:
Soldering plumbing lines
▶ Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
▶ Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
If the dishwasher came with a protective barrier, screw
through the barrier.
3. For Side Mount, lift the flap on the deco strip and insert
the 1/2" (12.7mm) wood screws underneath.
Note
Important notes for water connection:
¡ If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡ Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡ If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
¡ Always use appropriate seals when making plumbing
connections.
1. Flush the incoming water line for approximately 1
minute to clear any foreign material.
2. Connect the dishwasher water supply line to the water
shut off valve.
‒ Install a shut off valve if one isn’t already in the
supply line.
‒ Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
D
h
5ꢀDishwasher Connection
D
h
Follow these instructions to connect the dishwasher.
5.1ꢀInstalling the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120° F (49° C) water to the dishwasher.
Water that is too hot can cause some detergents to lose
3. Properly tighten all water connections.
12
| General | Details |
|---|---|
| Name | BOSCH SHE4AEM6N 100 Series Black Full Console Dishwasher |
| Make | Bosch |
| Language | English |
| Filetype | PDF (Download) |
| File size | 4.24 MB |
(1 votes, average: 5.00 out of 5)
Loading...
BOSCH SMV6ZCX49E-39 Dishwasher
BOSCH SMI4HVS33E Dishwasher
BOSCH SRV2HKX39G Dishwasher
BOSCH SGS4HAW40G Dishwasher
BOSCH SGH4HVX32G Dishwasher
BOSCH SMS4ECI26E Dishwasher
BOSCH SMS6EDW02G Free-Standing Dishwasher
BOSCH SMV4HTX27G Dishwasher
BOSCH SMV4HCX48E Dishwasher
BOSCH SPV4XMX28E Dishwasher
BOSCH SMH6TCX01E-38 Dishwasher
Whirlpool WDT740SAL 4 Inch Dishwasher
Bauknecht B7I HF60 Dishwasher
IKEA SBE6496E0G PROFFSIG Integrated Dishwasher
BOSCH SHX65CM5N Dishwasher
GE APPLIANCES GDT565HSYSS Energy Star Hybrid Tub Dishwasher
FORZA FD24DI Dishwasher
BOSCH 9000560760 Undercounter Dishwasher
BOSCH SMI8ZDS81T Dishwasher
BOSCH SBT6TB801E-46 Dishwasher