BOSCH SMS8ZDW86M Dishwasher
Cleaning filters
Cleaning the spray arms
Clean wastewater pump
1. After each wash check the filters for
residue.
5. Press the locking
1. Unscrew the upper spray arm
and
1. Disconnect the appliance from the power supply.
2. Remove the filter system.
3. Scoop out any water.
4. Prise off the pump cover using a
spoon and grip it by the crosspiece.
catches
to-
pull down to remove
.
gether and lift
2. Rotate the spray arm to the side to
make room for filter cleaning.
3. Turn the coarse
the coarse filter
out
.
filter anticlock-
wise
and re-
6. Clean the filter elements under running
water.
7. Re-assemble the filter system.
8. Insert the filter system into the appliance
and turn the coarse filter clockwise.
Make sure that the arrow markings
match up.
The spray arm will automatically return
to the correct position when starting, so
it is not necessary to reposition the
spray arm to the front.
2. Position the lower spray arm as shown
move the filter
system
, grip in the middle and pull up to re-
.
move
.
5. Lift the pump cover inwards at an angle and remove.
6. Remove any remnants of food and foreign bodies in the area
of the impeller.
4. Pull down the mi-
cro filter to re-
move.
7. Insert the pump cover
and press
3. Check the outlet nozzles on the spray arms for blockages un-
der running water and remove any foreign bodies.
4. Insert the lower spray arm again and push down.
Ensure that the spray arm is in the correct position.
a The spray arm clicks into position.
down
.
a The pump cover clicks into position.
5. Insert the upper spray arm and screw it firmly in place.
8. Install the filter system.
Troubleshooting
Fault
Cause and troubleshooting
Fault
Cause and troubleshooting
Fault
Cause and troubleshooting
E:3200 or indicator for
water supply lights up.
Supply hose is kinked.
E:9240 lights up.
Filters are soiled or blocked.
Removable streaks are
present on glasses, glass-
ware with a metallic ap-
pearance and cutlery.
Amount of rinse aid to be dispensed is set too high.
▶
▶
▶
Install the supply hose without kinks.
Clean the filters.
Set the rinse aid system to a lower setting.
Water tap is turned off.
E:6102 lights up.
Wastewater pump is blocked.
No rinse aid has been added.
▶
▶
▶
Turn on the water tap.
Clean the wastewater pump.
Add rinse aid.
Water tap is jammed or furred up.
Cover of the wastewater pump is loose
Rust spots on cutlery.
Cutlery is not sufficiently rust-resistant. Knife blades are often
more severely affected.
▶
▶
Turn on the water tap.
The flow rate must be at least 10 l/min when the water sup-
ply is open.
Secure the cover of the Wastewater pump so it clicks into
position.
▶
Use rust-resistant tableware.
Remnants of food on
tableware.
Tableware is placed too close together or basket is overfilled.
Cutlery may also rust if washed together with rusting items.
The filters in the water connection of the supply or AquaStop
hose are blocked.
1.
Arrange tableware with sufficient space in between.
The spray jets must reach the surfaces of the tableware.
Avoid points of contact.
▶
Do not wash rusting items.
Detergent residue is
present in the detergent rinsed out.
dispenser or the tablet
collecting tray.
Spray arms were blocked by tableware so detergent was not
1.
2.
3.
4.
5.
Switch off the appliance.
Pull out the mains plug.
Turn off the water tap.
Unscrew the water connection.
Remove the filter from the sup-
ply hose
2.
Spray arm rotation is blocked.
▶
Check that the spray arms are not blocked and can rotate
freely.
▶
Arrange tableware so that it does not obstruct spray arm ro-
tation.
All LEDs light up or flash Electronics have detected a fault.
or the rinse programme
does not continue run-
ning.
Spray arm nozzles are blocked.
▶
Press the main switch button for approx. 4 seconds.
The appliance is reset and restarted.
▶
Clean the Spray arms.
Filters are soiled.
▶
Clean the filters.
Filters are inserted incorrectly and/or not engaged.
1.
2.
Insert the filters properly.
Engage the filters.
6.
7.
8.
9.
10.
11.
Clean the filter.
Re-insert the filter in the supply hose.
Screw the water connection back on.
Check the water connection for leaks.
Restore the power supply.
Washing programme selected too weak.
▶
▶
Select a more intensive washing programme.
Adjust the sensitivity of the sensors.
Switch the appliance on.
| General | Details |
|---|---|
| Name | BOSCH SMS8ZDW86M Dishwasher |
| Make | Bosch |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.45 MB |
(1 votes, average: 5.00 out of 5)
Loading...
BOSCH SMV6ZCX49E-39 Dishwasher
BOSCH SMI4HVS33E Dishwasher
BOSCH SRV2HKX39G Dishwasher
BOSCH SGS4HAW40G Dishwasher
BOSCH SGH4HVX32G Dishwasher
BOSCH SMS4ECI26E Dishwasher
BOSCH SMS6EDI02G Free-Standing Dishwasher
BOSCH SMS6EDW02G Free-Standing Dishwasher
BOSCH SMV4HTX27G Dishwasher
BOSCH SMV4HCX48E Dishwasher
FAGOR AD-120CW Door Style Dishwasher
BOSCH SMS4HTI03E Dishwasher
JENNAIR W11745540A Dishwasher
BOSCH SPV4HMX10E Dishwasher
BOSCH 81739 Dishwasher
Hotpoint H8I HP42 Fully Integrated Dishwasher
BOSCH SMS4HMW26M Free-Standing Dishwasher
BOSCH SMH4ECX28E Dishwasher
BOSCH SHP88CL5N Custom Panel Dishwasher
IKEA RENGOERA Dishwasher