FISHER PAYKEL DD24DDFT9 Series Dishwasher

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

DOUBLE DISHDRAWER™ DISHWASHER  

CONTEMPORARY  

DD24DDFT9, DD24DA9, DD24DCT9, DD24DCHT9 & DD24DTN9  

PROFESSIONAL  

DD24DVT9  

INSTALLATION GUIDE  

US CA  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	FISHER PAYKEL DD24DDFT9 Series Dishwasher
Make	Fisher & Paykel
Language	English
Filetype	PDF (Download)
File size	1.38 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• Fisher & Paykel

FISHER PAYKEL DD24DDFT9 Series Dishwasher Overview

Summary of Contents

• Page 1: Double Dishdrawer™ dishwasher Installation guide
• Page 2: Safety and warnings Electric shock hazard Tip hazard Failure to follow this advice may result in electrical shock or death. This appliance must be earthed. If drawers are pulled open while product is not secured to cabinetry, product may tip. To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Installation of this DishDrawer requires basic mechanical and electrical skills. Ensure all water connections are turned off. The DishDrawer must be installed to allow for future removal from the enclosure if service is required. Ensure only supplied hoses are used for connection.
• Page 3: Tools and components are essential for installation. Parts supplied include various tools and components necessary for setup. Inspect the product for shipping damage upon receipt. Contact the dealer if any damage is detected. Fisher & Paykel is not responsible for shipping damage. Installation should be performed by a trained technician or qualified person. An install video provides an overview of the installation process. Optional components may vary by model. Some components come fitted to the product. Specific kits are required for different models.
• Page 4: Product dimensions — DD24DC models Overall height Overall width Overall depth Height of chassis Depth of chassis Height of upper door panel Height of lower door panel Depth of door panel Ventilation gap between door panels Actual product dimensions may vary by 1/16 (2 mm)
• Page 5: Product dimensions for DD24DA models are provided in both millimeters and inches. Overall height, overall width, and overall depth are key dimensions listed. The height of the chassis and the depth of the chassis are also specified. Heights of the upper and lower door panels are included. The depth of the door panel and the ventilation gap between door panels are mentioned. Minimum clearance between the toe kick panel and the floor is noted. The height from the base of the door to the floor is indicated. The maximum drawer extension from the front of the chassis is specified. The height from the top of the drawer panel to the top of the chassis is included. Actual product dimensions may vary by 1/16 (2 mm).
• Page 6: Product dimensions for DD24DD models include overall height, width, and depth measurements. Overall height ranges from 820 to 880 mm. Overall width is 23 9/16 inches. Overall depth is specified as 31 15/16 inches. Height of chassis and depth of chassis are also provided. Height of upper and lower door panels are detailed. Ventilation gap between door panels is mentioned. Minimum clearance between toe kick panel and floor is 1/2 inch. Height from base of door to floor varies from 3 15/16 to 6 5/16 inches. Actual product dimensions may vary by 1/16 inch (2 mm).
• Page 7: Product dimensions for DD24DV2T models include overall height, width, and depth measurements. Overall height ranges from 34 to 36 3/8 inches. Overall width options are 23 9/16, 22 9/16, 33 11/16, 21 3/4, 17 3/8, and 12 1/4 inches. Overall depth is specified, with additional details on chassis height and depth. Height of upper and lower door panels is provided, along with the depth of the door panel. Ventilation gap between door panels is noted. Minimum clearance between toe kick panel and floor is mentioned. Height from the base of the door to the floor varies based on adjustment. Max drawer extension from the front of the chassis is specified. Actual product dimensions may vary by 1/16 inch (2 mm).
• Page 8: Product dimensions – DD24DNT models Overall height: 32 1/4 - 34 5/8 inches Overall width: 23 9/16 inches Overall depth: 20 inches Height of chassis: 553 mm Depth of door panel: 15 11/16 inches Height of upper door panel: 12 3/16 inches Height from top of chassis to bottom of lower door panel: 28 3/8 inches Height from base of door to floor: 3 15/16 - 6 5/16 inches Max. drawer extension from front of chassis: 21 9/16 inches Actual product dimensions may vary by 1/16 (2 mm)
• Page 9: Cabinetry dimensions and clearances are essential for proper installation. Connections can be located in an adjacent cabinet on either side of the DishDrawer. Minimum clearance to adjacent cupboard door is 1/16 inch. Minimum inside height is specified. Inside width is 32 1/4 inches for standard models. Minimum clearance to corner cupboard is 13 inches. Minimum inside depth is 22 13/16 inches. Recommended height of adjacent cabinetry is between 3 15/16 and 6 5/16 inches. Height of toe kick area ranges from 100 to 160 mm. Refer to 'Plumbing & electrical considerations' and 'Cabinetry preparation' for more information on service requirements.
• Page 10: Plumbing and electrical considerations Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher & Paykel drain hose extension kit. Recommended water temperature: Hot (Maximum 140°F/60°C). Ensure water connection complies with local plumbing regulations. Water softener models: max. 1 MPa (145 psi), min. 0.1 MPa (14.5 psi). Non-water softener models: max. 1 MPa (145 psi), min. 0.03 MPa (4.3 psi). Drains will need to be separated to satisfy kosher requirements. We recommend confirming the acceptability with your local rabbi in respect to kosher installations. Dimensions taken from the chassis edge where applicable.
• Page 11: You have the option to hard-wire your DishDrawer™ Dishwasher. To do this, we recommend removing the supplied power cord and doing the hardwiring installation as close to the cavity as possible. Ensure only copper conductors are used. Slide the terminal block cover sideways to unlock and hinge open to access the terminal block. Open the lower drawer and press both locking tabs back to release. Unscrew the Live, Neutral and Earth wires as shown. Lift the drawer off the runners and carefully set aside on a protected surface. Safely cut the cord from the inside and outside of the product to remove the cord. Fit a suitable cable clamp for the conduit through the metal knockout. Ensure wiring is routed through or under housing ribs.
• Page 12: Hard wiring (optional) Screw down the Live, Neutral and Earth wires correctly. Refit module cover before sliding the access cover back into place, ensuring the 2 clips shown are fully locked. Before refitting the drawers, ensure the hoses are not twisted and all latches are facing forward. Refit the drawer back onto the runners, ensure both runners are extended halfway before lowering the tub. Slide the runners forward to engage.
• Page 13: Cabinetry preparation is essential for proper installation. Service access should be located on either side of the DishDrawer™ Dishwasher. Ensure edges are smooth and rounded if holes are created through wood. Fit the supplied edge protector if holes are created through metal. Route the power cord through a separate service hole from the hoses. Align the supplied moisture protection tape to the cabinetry. Ensure the area is free of debris before applying the tape. Select a cabinetry securing method: via brackets or drawer removal. If there are no side partitions, construct timber bracing for support. Follow the specified service hole dimensions for proper installation.
• Page 14: Secure to cabinetry via brackets (method A). Align bracket A with slot A and bracket B with slot B. Partially open one of the drawers and remove the first screw cover from the trim moulding. Ensure the ends of the brackets are not pushed into the chassis. Fit the two top brackets for additional stability. Pre-drilling a pilot hole may be required depending on the cabinetry material. Level the DishDrawer™ Dishwasher by carefully tipping it onto a protected surface. Rotate each leg anticlockwise to increase height, and clockwise to decrease. Push the product into the cavity, pulling the hoses through to avoid crushing or twisting them. Make minor adjustments by lightly tilting the product and rotating each leg as desired.
• Page 15: Secure to cabinetry via drawer removal (method B). Level the DishDrawer™ Dishwasher as required. Rotate clockwise to increase the height of each leg and anticlockwise to lower. Optionally, fit the two top brackets. Ensure the ends of the brackets are not pushed into the chassis. Loosen each foot by 1/2 a turn by lightly tilting the product. Push the product into the cavity, pulling the hoses through to avoid crushing or twisting them. Secure to cabinetry via all four fixing locations in the chassis. Before refitting the drawers, ensure the hoses are not twisted and all latches are facing forward. Lift the drawer off the runners and set aside on a protected surface.
• Page 16: Install toe kick for DD24DC, DD24DP, DD24DN, and DD24DD models. Measure toe kick height where it meets the bottom of the tub. Snap excess and smooth edges. Snap both end tabs. Carefully score toe kick at desired height. Slide toe kick onto the mounting rails and secure. Do not over tighten the screws.
• Page 17: Install toe kick – DD24DA models Measure the distance from the floor to the base of the lower door panel. Punch or drill out the two mounting holes with a 5mm drill bit on each side of the toe kick. Secure toe kick to the Dishdrawer using the supplied pins. Recommendations are based on the required minimum clearance of 12mm between the floor and toe kick. If the toe kick touches the floor with a full load, more of the panel may need to be removed. Remove the lower drawer. On a protected surface, carefully score down both corners to the desired cut-off point and snap to remove the excess. Refit the lower drawer. Smooth the edges using a file or knife as desired.
• Page 18: Plumbing & electrical connection Sink trap/waste tee installation Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights. Ensure the drain hose does not extend into water retained in the trap; an air gap is required to prevent waste water from siphoning back into the tub. Connect the inlet hose to tap and hand-tighten into place. Using a spanner or pliers, turn a further 180° to secure, avoiding over-tightening. Do not turn water supply on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled. Plug product in.
• Page 19: Plumbing & electrical connection Install your Air Gap Kit to the benchtop. We recommend using a Dual Air Gap Kit. Refer to ‘Plumbing & electrical connection’ for minimum install heights. Thread wire clips onto the hoses before fitting them to the hose joiner. Unplug or drill out the waste tee before securing to sink trap or waste tee. Connect the inlet hose to tap and hand-tighten into place. Using a spanner or pliers, turn a further 180° to secure. Avoid over-tightening. Do not turn water supply on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled.
• Page 20: Installer checklist Check all parts are installed correctly and are secure. Ensure all electrical tests have been conducted in accordance with local regulations. Ensure all clearance gaps have been maintained. Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the control panel. Ensure DishDrawer™ Dishwasher is securely fastened to the cabinetry and drawer opens and closes freely with no resistance. Ensure any packaging or tape securing the racks and spray arm is removed. Check the spray arm is in place, mounted correctly and rotates freely. Ensure any knock-outs or plugs in drain connection have been drilled out and drain connection has been made. Ensure inlet hose has supplied rubber washer fitted, and that it’s tightened.
• Page 21: Troubleshooting for DD24DD, DD24DV2T, DD24DT4N, and DD24DT4Z models includes checking power connection and activating auto power-on. Ensure the water supply is turned on to address water supply faults. Check for obstructions preventing the drawer from closing properly. Inspect hoses and connections for leaks around water supply and drain connections. Ensure the product is secured to cabinetry to prevent tipping. Verify that the spray arm is properly mounted and turns freely. Refer to the user guide for additional troubleshooting if problems persist. For warranty details, consult the Service & Warranty book or contact support. Troubleshooting for DD24DA, DD24DC, and DD24DT2N models includes ensuring the drainage hose is not blocked. Check that the spray arm is firmly seated and functioning correctly.