JennAir Dishwasher
ADDED ADDED
CAN BE
SELECTED WHAT IT DOES
WITH
TIME
TO
WATER
GALLONS
OPTIONS
CYCLE (LITERS)
Cookware,
Sensor,
Normal,
Rapid
Dries dishes with heat. Load plastic
Dries dishes with heat
or with heat and fan on
some models (default
on with some models).
item in upper racks.
Up to
NA
Precision
Dry
0:63
Dries dishes with heat and a fan.
Load plastic item in upper racks.
Cookware,
Sensor,
Normal
Increases the Energy used for drying
the dishes. This may lengthen the
cycle time.
Dries dishes with heat
or with heat and fan on
some models.
Up to
NA
Precision
Dry Max
1:23
DISHWASHER FEEDBACK
CONTROL
PURPOSE
COMMENTS
If the door is opened during a cycle or power is interrupted,
START/RESUME indicator light flashes. Cycle will not
RESUME until door is closed and START/RESUME is pressed.
Press to start or resume a
wash cycle.
START/RESUME
NOTE: Push door firmly closed within 4 seconds of pressing
START/RESUME. If door is not closed within 4 seconds, the
START/RESUME button light will flash, an audible tone will be
heard, and cycle will not start.
Push to reset any cycle or
Close door firmly. The dishwasher starts a 2 minutes drain (if
needed). Let dishwasher drain completely.
CANCEL/DRAIN options during selection. Push
to end a cycle once started.
To delay the start:
1. Select a wash cycle and options.
2. Press Delay. Each time you press Delay, it will display the
Runs the dishwasher at a later
time.
Delay
next available delay time.
3. Press START to begin the delay countdown.
NOTE: If the door is opened, such as to add a dish, the Start
button must be pressed to resume the delay countdown.
Cancelling a Cycle
Adding a Dish After Dishwasher is Started
1. Open the door slightly to stop the cycle. Wait for the spraying
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop before completely opening the door.
action to stop, then open the door completely.
2. Press and hold CANCEL/DRAIN for 4 seconds. The
2. Check whether the detergent dispenser cover is still closed.
If it is open, the wash cycle has already started and adding a
dish is not recommended.
CANCEL/DRAIN light will turn on.
3. Close the door, and the dishwasher starts a drain cycle (if
water remains in bottom of dishwasher). Let the dishwasher
drain completely. The CANCEL/DRAIN light turns off after
3 minutes.
3. If detergent has not yet been used (detergent dispenser cover
is closed), you may add a dish.
4. Push door firmly closed and press START/RESUME within
4 seconds. If you take too long, the Start keypad light flashes,
and you will hear an audible tone. Press START/RESUME
again and close the door within 4 seconds.
Changing a Cycle After Dishwasher Is Started
You can interrupt a cycle and restart the dishwasher from the
beginning using the following procedure.
1. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
2. Check that detergent dispenser cover is still closed. If cover
is open, you will need to refill the detergent dispenser before
restarting the new cycle.
3. Press CANCEL/DRAIN to reset the control.
4. Select new cycles and options.
5. Press START/RESUME.
| General | Details |
|---|---|
| Name | JennAir Dishwasher |
| Make | JENNAIR |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.42 MB |
(1 votes, average: 5.00 out of 5)
Loading...
JennAir QQSCHIB Dishwasher
JENNAIR JDPSS24 Series Dishwasher
JENNAIR JDPSG244LS Dishwasher
JENNAIR W11680101A Dishwasher
JENNAIR W11745540A Dishwasher
JENNAIR JDTS3924SP Dishwasher
JENNAIR JDAF5924RX Flush Mount Panel Ready Dishwasher
JENNAIR W11680101 Dishwasher
JENNAIR JDPSS246LL Dishwasher
EdgeStar DWP63BL Countertop Dishwasher
Haier HDW15F1B1 Dishwasher
GE CGP6030 30 Inch Gas Cooktop with Dishwasher
BOSCH SBV6ECX00E/38 Fully Integrated Dishwasher
Bosch SMU4HTW02H-01 Dishwasher
BOSCH SPS4EMW61E Dishwasher
BOSCH SMS6ZCI01P Dishwasher
Midea MDF18A1A Series Dishwasher
MAYTAG MDB Series Dishwasher
FISHER AND PAYKEL DD24ST4NX9 Single DishDrawer Dishwasher