Home > KitchenAid > KitchenAid W10242569C Compactor Dishwasher
KitchenAid W10242569C Compactor Dishwasher
Cabinet-face Mounting
Installation
1. Remove the 2 rubber bumpers from the lower corners of the
inside drawer front. Set aside the bumpers and discard the
screws.
C
D
A
2. Align the bottom of the custom panel with the bottom of the
exterior drawer front and rest the panel on the rest tab.
NOTE: The bottom of the custom panel should not extend
below the bottom rest tab at the lower center of the exterior
drawer front.
B
3. Secure the custom panel to the exterior drawer front by using
four #8 x 1" wood screws from the inside drawer front.
■
Install the top 2 wood screws as shown.
■
Use the bottom 2 wood screws to also re-install the
2 rubber bumpers on each side of the lower inside drawer
while attaching to the custom panel.
A. Mounting clip
B. Cabinet
C. Retaining bracket
D. Mounting screw
8. Grasp sides of the compactor drawer and place the bottom
of the drawer into the tracks.
4. Attach a 15" x 1/2" (38.1 cm x 13 mm) quarter-round filler
along the top inside edge of the drawer front using glue or
screws.
9. Lift at the handle so the drawer will go over the drawer stops.
10. Close the drawer.
A
11. Check that the drawer opens freely. If the toe plate rubs
against the floor, see “Adjusting the Toe Plate” for further
instructions.
Adjusting the Toe Plate
D
B
C
If the toe plate rubs the floor covering, the toe plate clearance
may be changed as follows:
1. Mark on each side of the toe plate the amount of toe plate
that rubs the floor covering.
D
2. Remove the drawer from the unit. See Step 3 in the
“Unpacking” section.
3. Use a ruler and a pencil or chalk to draw a line between the
marks on each side of toe plate.
E
4. Use scissors or utility knife to cut toe plate along line.
5. Replace the drawer. If the toe plate still rubs the floor
covering, repeat steps 1 to 4.
Installing a Custom Panel
Dimensions
A. Custom panel
B. 15" x 1/2"
(38.1 cm x 13 mm) quarter-
round filler
D. #8 x 1" wood screws
placement
Use these dimension drawings to create a custom panel for use
without a trim kit. The panel should be a minimum of 1/2"
(13 mm) thick.
E. Rubber bumper (one on
each side)
C. Drawer front
29 ³⁄₈"
(74.6 cm)
15"
(
)
38.1 cm
6
| General | Details |
|---|---|
| Name | KitchenAid W10242569C Compactor Dishwasher |
| Make | KitchenAid |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.7 MB |
(1 votes, average: 5.00 out of 5)
Loading...
KitchenAid KDTE304RBS Third Level Jet Rack Dishwasher
KitchenAid KDTF324PPA Dishwasher
Kitchenaid MVWC565FW1 Dishwasher
KitchenAid w11323304 Dishwasher
KitchenAid KDFE104KWH Two Rack Dishwasher
KitchenAid KDTE104KPS Dishwasher
KitchenAid KDFE104KBL Front Dishwasher
KitchenAid KDTF924PPS Flush Cabinet Dishwasher
KitchenAid KDTE304RBS Level Jet Rack Dishwasher
KitchenAid KDF Series Dishwasher
FISHER and PAYKEL DW60UC2X Contemporary Builtunder Dishwasher
FISHER AND PAYKEL DD24DTX6PX1 Dishwasher
BOSCH SPS4EMW28E Dishwasher
BOSCH SMH4HCX48E Dishwasher
SIEMENS SN13ES78CS Dishwasher
BOSCH SPS4HMI61E Dishwasher
Fisher and Paykel DD24DHTI9 N Dishwasher
Miele G 7131 SCi AD 125 Edition Dishwasher
BOSCH BSH21 Dishwasher
FISHER and PAYKEL DD60SDFHTX9 Contemporary Tall Dishwasher