Home > KitchenAid > KitchenAid W10242569C Compactor Dishwasher
KitchenAid W10242569C Compactor Dishwasher
Undercounter Installation
NOTE: Proper installation is your responsibility. Make sure you
2. Use pliers to lower the leveling legs away from the cabinet.
Adjust the legs so there will be a 1/8" (3 mm) to 1/4"
have everything necessary for correct installation. It is the
personal responsibility and obligation of the customer to contact
a qualified installer to assure that electrical installation meets all
National and Local codes and ordinances.
(6.4 mm) space between the top of the compactor and the
top of the cabinet opening. Stand the compactor upright.
3. For model with cabinet, remove the plastic plugs from the
compactor cabinet top.
Tools Needed
Gather the required tools and parts before starting installation.
4. Move the compactor close to its final position.
5. Plug into a grounded 3 prong outlet.
6. Determine if you want the compactor frame or drawer front
flush with the cabinet front.
■
■
■
■
Level
■
■
■
■
Phillips screwdriver
Flat-blade screwdriver
⁵⁄₁₆" box-end wrench
Utility knife
Tape measure
Pliers
Using the two #8-18 x 5/16" screws, install the retaining
brackets to cabinet top as needed:
Scissors
IMPORTANT:
■
■
■
If the compactor frame is to be flush with the cabinet
front, place retaining bracket screws through “1.”
■
Do not grasp control panel to move compactor.
If the compactor drawer front is to be flush with the
cabinet front, place retaining bracket screws through “3.”
■
Slide compactor onto cardboard or hardboard before moving
compactor across floor to avoid floor covering damage.
If the compactor is to be midway between “1” and “3,”
place the retaining bracket screws through “2.”
■
Do not allow the rear frame of the compactor to touch the
floor covering when lifting or moving compactor.
A
B
Undercounter Installation
NOTE: Installation hardware is not provided with full cabinet
models.
3
2
1. Measure the height of your cabinet opening. The top of the
compactor should be at least 1/8" (3 mm) from the top of
the cabinet opening.
1
The rear wheels are preset for a cabinet opening height of
34¹⁄₄" (87 cm) (Position 1).
To adjust for other cabinet opening heights:
A. Countertop
■
Loosen self-tapping screw just enough to clear stud from
hole in position 1.
B. Retaining bracket
■
Move the rear wheel and stud to position 2 or 3 as
needed for your cabinet opening measurement:
7. Slowly lift the front slightly and roll compactor into the cabinet
opening.
Position 2: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm)
Using the two #8-18 x 1/2" screws, fasten the retaining
brackets to the countertop with the mounting screws.
Position 3: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm)
NOTE: To level the unit in position 3, you may need to
add shims under the leveling legs.
If brackets cannot be attached to the underside of
countertop, attach mounting clips to brackets. Fasten
compactor to cabinet front with mounting screws through
mounting clips.
■
■
Tighten screw.
Repeat for other rear wheel.
Countertop Mounting
B
A
1
2
3
C
B
C
A
A. Countertop
C. Mounting screw
D
B. Retaining bracket
A. Wheel bracket assembly
B. Cabinet
C. Locating stud
D. Self-tapping screw (pivot)
5
| General | Details |
|---|---|
| Name | KitchenAid W10242569C Compactor Dishwasher |
| Make | KitchenAid |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.7 MB |

KitchenAid KDTE304RBS Third Level Jet Rack Dishwasher

KitchenAid KDTF324PPA Dishwasher

Kitchenaid MVWC565FW1 Dishwasher

KitchenAid w11323304 Dishwasher

KitchenAid KDFE104KWH Two Rack Dishwasher

KitchenAid KDTE104KPS Dishwasher

KitchenAid KDFE104KBL Front Dishwasher

KitchenAid KDTF924PPS Flush Cabinet Dishwasher

KitchenAid KDTE304RBS Level Jet Rack Dishwasher

KitchenAid KDF Series Dishwasher


























