KUCHT K6502D Dishwasher
Installation Instructions
STEP 14 CONNECT POWER
SUPPLY
Skip this step if equipped with power cord.
STEP 15 PRE-TEST CHECKLIST
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered
by your warranty.
Verify that power is turned off at the source.
• Remove junction box cover “A”.
Check to be sure power is OFF.
• Locate the three dishwasher wires, (white, black
and green) with stripped ends. Insert dishwasher
wires through the small hole in the junction box “B”.
• Secure house wiring to the bottom of the junction
box with a strain relief “C”.
Open door and remove all foam and paper packaging.
Locate the Owner’s Manual in the literature package.
Read the Owner’s Manual for operating instructions.
• Use wire nuts to connect incoming ground to green,
white to white and black to black “D”.
• Replace junction box cover “E”. Check to be sure
that wires are not pinched under the cover.
Check door opening and closing. If door does not
open and close freely or tends to fall, check spring
adjustments. See Step 1.
Check to be sure that wiring is secure under the
dishwasher, not pinched or in contact with door
springs or other components. See Step 9.
A
Remove
Junction Box
Cover
B Check That White, Black and
Green Dishwasher Wires Are Threaded
Thru Hole in Back
Check door alignment with tub. If door hits tub,
level dishwasher. See Step 10.
White
Ground
Black
Pull lower rack out, about half way. Check to be
sure it does not roll back or forward on the door.
If the rack moves, adjust leveling legs. See Step 10.
Check door alignment with cabinet. If door hits cab-
inet, reposition or relevel dishwasher. See Step 10.
D
Use UL Listed
Wire Nuts
Verify water supply and drain lines are not kinked
or in contact with other components. Contact with
motor or dishwasher frame could cause noise. See
Step 8.
C
Insert Power
Cord Wires Thru
Strain Relief
and Tighten
Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be
between 120°F and 150°F. A minimum of 120°F tem-
perature is required for best wash performance.
See “Prepare Hot Water Line,” page 5.
E. Replace Junction Box Cover
WARNING
If house wiring is not 2-wire with
ground, a ground must be provided
by the installer. When house wiring
is aluminum, be sure to use cUL/UL Listed
anti-oxidant compound and aluminum-
to-copper connectors
Add 2 litres of water to the bottom of the dish-
washer to lubricate the pump seal.
Turn on water supply. Check for leaks. Tighten con-
nections if needed.
Remove protective film if present from the control
panel and door.
11
| General | Details |
|---|---|
| Name | KUCHT K6502D Dishwasher |
| Make | Kucht |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1 MB |
(1 votes, average: 5.00 out of 5)
Loading...
KUCHT KD240PR Panel Ready Dishwasher
BOSCH SMS6ZCI42E Free-Standing Dishwasher
FISHER PAYKEL DW60FC6X1 Dishwasher
FISHER and PAYKEL DD60DDFHX9 Dishwasher
BOSCH SMS6EMI65M Dishwasher
BOSCH SHX53CM5N Bar Handle Dishwasher
IKEA OSTVEDA Dishwasher
Bosch 1071797 SMS Dishwasher
gorenje GI62040X Dishwasher
FISHER PAYKEL DD60DTX6I1 Integrated Dishwasher
FRIGIDAIRE FDPC4314A Dishwasher