MONOGRAM UDT165SIVII 18 Inch Dishwasher

1

2

Top of Panel  

Top of Panel  

2-5/32"  

(5.5 cm)  

2-5/32"  

(5.5 cm)  

7-11/16"  

(19.5 cm)  

7-11/16"  

(19.5 cm)  

Drill 3/32"  

Drill 3/32"  

Pilot Hole  

Pilot Hole  

3/32" Deep  

3/32" Deep  

STEP 4 INSTALL MOUNTING SCREWS AND SPACERS  

3/4" Thick Custom Panel  

Template Instructions for  

18" Top Control Integrated  

Dishwasher Models  

Note: The custom panel is secured to the dishwasher door  

with the metal spacers, screws and brackets provided.  

The metal spacers and brackets will slip into the slots  

on the dishwasher door and control panel.  

• Align the metal spacers over the top pilot holes. Ensure  

the thick, recessed side is facing up.  

• Drive the supplied 1" (2.54 cm) Phillips flat-head screws  

through the metal spacers and into the panel.  

• Align the brackets over the bottom pilot holes. Ensure  

the curved lip is facing up. If the surface of the  

panel is not flat, use the spacer pads provided.  

• Drive the 5/8" (1.58 cm) Phillips flat-head screws through  

the brackets and into the panel.  

Bracket  

The custom panel should be sized to your installation situation. See Step 1. For easier installation, the  

custom panel and custom handle should be attached before installing the dishwasher. Use this template  

to locate mounting screws and spacers on the custom panel.  

Spacer  

Spacer Pad  

IMPORTANT  

PARTS INCLUDED:  

(2) Brackets  

(4) 5/8" (1.58 cm) Phillips flat-head screws  

(2) Spacer pads  

(2) Metal spacers  

STEP 5 INSTALL CUSTOM HANDLE  

• A custom handle must be installed onto the custom  

panel. Install the custom handle 4-1/2" max. from the  

top of the panel.  

Screws must be  

countersunk into panel  

4 1/2"  

A custom handle must be installed onto the panel  

before the panel is secured to the dishwasher door.  

• The handle should be installed so that it aligns  

with adjacent drawer handles, or 4-1/2" (115 mm)  

max. from the top of the panel. Secure the handle  

in the same manner as the cabinet handles.  

Screws must be countersunk into the panel.  

(115 mm)  

Max.  

from top  

of panel  

(2) 1" (2.54) Phillips flat-head screws  

(2) 1-1/2" (3.81 cm) Phillips flat-head screws  

Handle  

Custom  

door panel  

STEP 1 CUSTOM PANEL SIZE REQUIREMENTS  

HEIGHT  

WIDTH  

Panel height should be 26-13/16" (68.1 cm).  

Panel width must be 17-1/2" (44.4 cm).  

• If the panel width is less than 17-1/2" (44.4 cm), it  

will not cover the dishwasher frame.  

STEP 6 INSTALL ASSEMBLED PANEL  

• The top of the custom panel must be flush  

with the top of the door. The 1/2" (1.27 cm)  

minimum gap between the top of the door and  

the bottom of the countertop must be maintained.  

• Secure the panel to the door by inserting  

the top metal spacers and bottom brackets  

into the matching slots on the dishwasher  

door and control panel.  

• Make sure both metal spacers  

and both brackets engage the slots.  

• Press the panel against the door and push  

IMPORTANT: To ensure optimum door balance  

performance, the custom panel must not weigh  

more than 8 lbs.  

Trim  

Around  

Dotted  

Line  

Dishwasher  

door  

Countertop  

downward until the metal spacers and brackets  

are fully engaged into the slots. The panel  

should align evenly with the top and sides.  

1/2" (1.27 cm)minimum  

Minimum 1/2" (1.27 cm)  

gap for clearance  

Custom panel  

• Stand the dishwasher upright.  

• Open the dishwasher door and remove the first  

side screw from the top on each side of the inner  

door.  

STEP 2 DRAW CENTERLINE  

• Place the custom panel on a flat surface with the  

appearance side down.  

• Replace these screws with the 1-1/2” (3.81 cm)  

Phillips flat-headed screws and drive them through  

the inner door and into the custom panel.  

• Locate the vertical center of the panel at the top.  

• Use a carpenter's square to draw a centerline from  

top to bottom.  

IMPORTANT: Do not overtighten screws.  

Excessive tightening of the screws could damage  

door edges.  

Custom  

panel  

Adjust both sides equally  

STEP 7 CHECK DOOR BALANCE  

STEP 3 ALIGN TEMPLATE TO PANEL  

To check the door balance, hold the top of the  

dishwasher firmly.  

• Trim template on the dotted line along all sides.  

• Place the template on the panel aligned with the top  

edge and the centerline. Use tape to hold in place.  

• Check the door balance by opening and  

closing the door.  

IMPORTANT: If the template is not aligned with the top  

Turn  

clockwise  

to increase  

• If the door drops when released, increase the  

spring tension. If the door rises when released,  

decrease the spring tension.  

edge of the panel, the 1/2" (1.27 cm) minimum gap will not  

be maintained. This 1/2" (1.27 cm) minimum gap must be  

maintained to prevent condensation and damage to the  

control panel from screw heads.  

• Use an awl to mark the screw hole locations indicated  

on the template. Remove the template.  

Turn  

• Using a T25 torque driver or socket wrench  

(as appropriate), adjust in the direction shown.  

Adjust both sides equally.  

Mark center  

screw holes  

counterclockwise  

to decrease  

13/32"  

(1 cm)  

13/32"  

(1 cm)  

5-29/32"  

(15 cm)  

5-29/32"  

(15 cm)  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

PARTS SUPPLIED  

6-1/2"  

(16.5 cm)  

6-1/2"  

(16.5 cm)  

(2) Metal spacers  

(2) Brackets  

(2) Spacer Pads  

(Optional)  

(4) 5/8" (1.58 cm)  

Phillips flat-head  

screws  

(2) 1" (2.54 cm)  

Phillips flat-head  

screws  

(2) 1-1/2" (3.81 cm)  

Phillips flat-head  

screws  

0120501700  

31-4000281 Rev 1  

11-22 GEA  

Trim Around Dotted Line  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	MONOGRAM UDT165SIVII 18 Inch Dishwasher
Make	MONOGRAM
Language	English
Filetype	PDF (Download)
File size	0.74 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• MONOGRAM

MONOGRAM UDT165SIVII 18 Inch Dishwasher Overview

Summary of Contents

• Page 1: Step 4: Install mounting screws and spacers The custom panel is secured to the dishwasher door with the metal spacers, screws, and brackets provided. Align the metal spacers over the top pilot holes. Drive the supplied 1 Phillips flat-head screws through the metal spacers and into the panel. Align the brackets over the bottom pilot holes. Drive the 5/8 Phillips flat-head screws through the brackets and into the panel. Step 5: Install custom handle A custom handle must be installed onto the custom panel. The handle should be installed so that it aligns with adjacent drawer handles or 4-1/2 max from the top of the panel. Step 1: Custom panel size requirements Panel height should be 26-13/16 (68.1 cm). Panel width must be 17-1/2 (44.4 cm). Step 6: Install assembled panel The top of the custom panel must be flush with the top of the door. To ensure optimum door balance performance, the custom panel must not weigh more than 8 lbs. Step 2: Draw centerline Locate the vertical center of the panel at the top. Use a carpenter's square to draw a centerline from top to bottom. Step 3: Align template to panel Place the template on the panel aligned with the top edge and the centerline. Use an awl to mark the screw hole locations indicated on the template. Step 7: Check door balance To check the door balance, hold the top of the dishwasher firmly. If the door drops when released, increase the spring tension.
• Page 2: ÉTAPE 4 INSTALLER LES VIS DE MONTAGE ET LES RONDELLES Le panneau sur mesure est fixé à la porte du lave-vaisselle à l’aide des espaceurs métalliques, des vis et des supports fournis. Alignez les espaceurs métalliques sur les trous guides supérieurs. Vissez les vis à tête plate Phillips 1 po à travers les espaceurs métalliques puis dans le panneau. Assurez-vous que la lèvre incurvée est orientée vers le haut. Vissez les vis à tête plate Phillips 1.58 cm (5/8 po) à travers les supports puis dans le panneau. Le panneau de finition doit avoir des dimensions appropriées pour l’installation. Pour faciliter l’installation, le panneau de finition et la poignée de finition doivent être montés avant la mise en place du lave-vaisselle. ÉTAPE 5 INSTALLATION DE LA POIGNÉE DE FINITION Il faut installer une poignée de finition sur le panneau de finition. Installer la poignée à moins de 11,5 cm (4-1/2 po) du haut du panneau. ÉTAPE 1 TAILLE NÉCESSAIRE POUR LE PANNEAU SUR MESURE Le panneau doit avoir au moins 44.4 cm (17-1/2 po) de largeur. Le haut du panneau sur mesure doit affleurer le haut de la porte. ÉTAPE 6 INSTALLATION DU PANNEAU ASSEMBLÉ Fixez le panneau à la porte en insérant les espaceurs métalliques supérieures et les supports inférieurs. IMPORTANT : Pour que la porte fonctionne bien, le panneau sur mesure ne doit pas peser plus de 6,4 kilos (14 livres). ÉTAPE 2 TRAÇAGE DE L’AXE Avec une équerre de menuisier, tracer un axe du haut au bas. IMPORTANT : Il ne faut pas serrer les vis en excès. ÉTAPE 3 ALIGNER LE GABARIT SUR LE PANNEAU Couper le gabarit suivant le pointillé, sur tous les côtés. Vérifiez l’équilibre en ouvrant et fermant la porte. LES PIÈCES ONT FOURNI (2) Espaceurs métalliques (2) Supports (2) Coussinets d’espacement