MONOGRAM ZDT925SINII Dishwasher

1

2

Trim Around Dotted Line  

10”-13/16”  

Trim Around Dotted Line  

10”-13/16”  

STEP 6  

INSTALL ASSEMBLED PANEL - (CONTINUED)  

3/4” Thick Custom Panel  

Template Instructions for  

Top Control Integrated  

Dishwasher Models  

Drill 3/32”  

Pilot Hole  

3/32” Deep  

Drill 3/32”  

Pilot Hole  

3/32” Deep  

Due to location of screw holes and very limited space it will be very helpful to attach screws to the driving bit with  

WDSHꢀWRꢀNHHSꢀWKHꢀVFUHZꢀIURPꢀIDOOLQJꢀRႇꢀLQVLGHꢀWKHꢀGRRUꢀZKLOHꢀLQVHUWLQJꢀGRZQꢀLQVLGHꢁꢀ5HDGꢀDQGꢀIROORZꢀWKHꢀVWHSVꢀEHORZꢁ  

1. Insert one of the supplied #8 x  

5/8” truss head screws through a  

piece of masking tape.  

2. Insert a minimum 2” long bit into  

head and wrap tape around end of  

bit. (#1 square drive preferred)  

3. Use a bit extension with a max 3/8”  

diameter shank and a minimum  

2-3/4” length.  

The custom panel should be sized to your installation situation. See Step 1.  

It is highly recommended that the custom panel be attached before installing the dishwasher.  

Use this template to locate mounting screws and spacers on the custom panel.  

CAUTION  

It is extremely important that the 2 screws are driven into the wood panel through the  

PHWDOꢀGRRUꢀDVVHPEO\ꢁꢀ7KLVꢀORFNVꢀWKHꢀYHUWLFDOꢀPRWLRQꢀRIꢀWKHꢀFXVWRPꢀSDQHOꢀDQGꢀLIꢀQRWꢀVHFXUHGꢀWKHꢀSDQHOꢀFDQꢀFRPHꢀRႇꢀ  

the unit during door opening/closing causing personal injury and damage to the panel.  

IMPORTANT  

PARTS INCLUDED:  

(4) Spacers  

(2) #8 x 5/8” Phillips truss head stainless steel screws  

(4) #8 x 7/8” Phillips truss head stainless steel wood screws  

(2) Heavy duty springs  

ꢀ A custom handle must be installed onto the  

custom panel. Install the custom handle  

4-1/2” max. from the top of the panel.  

4. Carefully open the door because door will likely be unbalanced.  

6WDUWꢀLQVHUWLRQꢀRIꢀGULYHUꢀDWꢀDSSUR[LPDWHO\ꢀꢂꢃÛꢀDQJOHꢀWRꢀFOHDUꢀWKHꢀVFUHZꢀKHDGꢀSDVWꢀWKHꢀKLQJHꢀFRPSRQHQWVꢄꢀRQFHꢀWKHꢀ  

screw head is clear, rock the driver forward to a vertical position. Proceed to drive the screw. Repeat procedure for  

the opposite side.  

STEP 1  

CUSTOM PANEL SIZE REQUIREMENTS  

Door shown fully open  

HEIGHT  

ꢀ The bottom of the custom panel must not overhang the  

bottom of the metal panel. Exceeding this will cause the  

custom panel to hit the toe kick and the door will not  

fully open. Any extra length of the custom panel must  

overhang at the top of the door.  

Panel height must be between 29-13/16” and 30-1/4”.  

IMPORTANT: It is  

extremely important  

Custom Panel  

29-13/16” Min.  

30-1/4” Max.  

to make sure the lower  

vent is present and  

is not obstructed by  

the custom panel.  

Lower vent must be clear.  

Install custom panel above  

the lower vent.  

2

1

Custom  

Panel  

Drive screw through the hole in  

hinge bracket and door into the  

wood panel.  

NOTICE: Do not overtighten screws.  

Excessive tightening of the screws  

could damage door edges.  

WIDTH  

Minimum 1/2” gap for  

clearance above top of  

metal dishwasher panel  

23-3/4”  

Panel width must be 23-3/4”.  

ꢀ If the panel width is less than  

23-3/4” it will not cover the  

dishwasher door frame.  

ꢀ If the panel height is more than 30-1/4”, it will prevent  

WKHꢀGRRUꢀIURPꢀ¿WWLQJꢀXQGHUꢀWKHꢀFDELQHWꢁ  

3

Countertop  

Hinge  

ꢀ If the panel height is less than 29-13/16” it will not cover  

the dishwasher door frame.  

IMPORTANT: To ensure optimum  

door balance performance, the  

custom panel must not weigh  

more than 20 lbs.  

1/2”  

min.  

Top of metal  

dishwasher panel  

Inner Door  

Installed screw  

STEP 2  

DRAW CENTERLINE  

ꢀ 3ODFHꢀWKHꢀFXVWRPꢀSDQHOꢀRQꢀDꢀÀDWꢀVXUIDFHꢀZLWKꢀDSSHDUDQFHꢀVLGHꢀGRZQꢁ  

ꢀ Locate the vertical center of the panel at the top.  

ꢀ Use a carpenters square to draw a centerline from top to bottom.  

STEP 7  

INSTALL DOOR SPRINGS  

Side  

of  

Panel  

ꢀ Depending on the weight of the panel being used, additional springs may be needed to balance the  

door during operation. If only one spring is being attached to the cable, the spring hook should be  

inserted into the middle hole on the cable and the other end of the spring should be hooked on the rear  

tub bracket as shown below:  

Side  

of  

Panel  

25-5/16”  

25-5/16”  

STEP 3  

ALIGN TEMPLATE TO PANEL  

Single spring: Hook into middle hole  

Hook on the rear tub bracket  

ꢀ Trim template on the dotted line along all sides.  

ꢀ Place template on the panel aligned with the bottom edge and the centerline.  

Use tape to hold in place.  

ꢀ If multiple springs are required on each side to balance the door, the spring hooks should be inserted  

into the top and bottom holes on the cable as shown below:  

IMPORTANT: If the template is not aligned properly with the panel, the  

panel may hit the toe kick and the door will not fully open. Longer panels  

should overhang at the top of the door. Make sure after installation, to  

maintain a minimum 1/8” gap to the countertop from the custom panel.  

Two Springs: Hook into  

top and bottom holes  

Hook bottom spring into the bottom (back) hole  

on base rail and hook the top spring into the  

Mark Center  

Screw Holes  

middle (side) hole on the same base rail  

ꢀ Use an awl to mark the screw hole locations indicated on the template.  

Remove the template.  

ꢀ The bottom spring opposite end should be hooked into the bottom (back) base rail hole as shown below. The top  

spring hooks into the middle hole (side) on the same base rail. See illustrations below.  

ꢀ The following table may be used as a guideline regarding which springs to use, depending on the weight of panel  

being added. However, spring combinations may be adjusted based on personal preferences regarding door feel.  

STEP 4  

INSTALL MOUNTING SCREWS AND SPACERS  

Panel Weight (lbs)  

Left Side Springs  

Blue  

Right Side Springs  

Spring Strength  

If the panel is less than 3/4” thick, shorter screws must be used. Use #8 x 3/4”  

screws for 1/2” thick panels (not supplied).  

0-5  

Blue  

Blue  

Gray  

Light Duty  

Medium Duty  

Heavy Duty  

5-10  

Gray x 2  

Blue  

ꢀ Use a 3/32” drill bit to drill pilot holes 3/32” deep in the marked locations.  

Make sure not to drill all the way through the panel.  

10-15  

15-20  

Blue x 2  

Black  

Black  

Black and Blue  

Black and Blue  

NOTE: The custom panel is secured to the dishwasher door with the spacers  

and screws provided. The 4 spacers will slip into the keyhole slots on the  

dishwasher door.  

ꢀ Close and latch the door.  

Screw  

Spacer  

ꢀ Check door balance after custom panel is installed.  

ꢀ Drive the supplied #8 x 7/8” screws through the spacer and into the panel.  

ꢀ Install remaining spacers and screws as indicated in the marked locations.  

ꢀ If the door drops open too fast, you may swap any of the springs with the next heaviest spring as shown in the table.  

ꢀ Remove the rear screw-style leveling feet if there is spring interference.  

Custom  

door  

STEP 5  

panel  

INSTALL CUSTOM HANDLE  

Screws Must  

Be Countersunk  

Into Panel  

Side View  

A custom handle must be installed onto the panel before the panel is secured  

to the dishwasher door.  

4-1/2" Max.  

From Top  

of Panel  

ꢀ The handle should be installed so that it aligns with adjacent drawer handles,  

or 4-1/2” max. from the top of the panel. Secure the handle in the same  

manner as cabinet handles. Screws must be countersunk into the panel.  

Handle  

Custom  

Door Panel  

Custom  

Panel  

STEP 6  

INSTALL ASSEMBLED PANEL  

For Double  

For Single Spring:  

Hook onto the rear  

tub bracket  

Springs: Hook  

bottom spring  

into bottom  

(back) hole on  

base rail and  

hook top spring  

into middle  

ꢀ Secure the panel to the door by inserting the top and bottom  

spacers into the matching keyhole slots.  

Dishwasher  

Door  

ꢀ Make sure all 4 spacers engage the keyhole slots.  

Front  

View  

Spacers  

Engage Keyhole  

Slots  

ꢀ Press the panel against the door and push downward until the  

spacers are fully engaged into the keyhole slots. The panel should  

align evenly with the top and sides.  

(side) hole in  

base rail  

Make sure  

pulley cables  

are within pulley  

shoulders  

TIP: If the door does not open easily or falls too quickly, check spring cable routing. The cable is held in place by  

“shoulders” on the pulley. Check to be sure the cable has not slipped over the pulley shoulders.  

IMPORTANT: Adjust both balance springs to the same amount of tension to prevent excessive door twisting during use.  

10”  

10”  

Drill 3/32”  

Pilot Hole  

3/32” Deep  

Drill 3/32”  

Pilot Hole  

3/32” Deep  

2-9/16”  

2-9/16”  

31-4000217-2  

Trim Around Dotted Line  

Trim Around Dotted Line  

09-23 GEA  

Align this with bottom edge of the door only. (Do not block vent exit).  

Bottom of Panel  

Bottom of Panel  

Do Not Block Vent Exit - See STEP 1  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	MONOGRAM ZDT925SINII Dishwasher
Make	MONOGRAM
Language	English
Filetype	PDF (Download)
File size	1.3 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• MONOGRAM

MONOGRAM ZDT925SINII Dishwasher Overview

Summary of Contents

• Page 1: Trim around dotted line for custom panel sizing. Install assembled panel instructions for top control integrated dishwasher models. Drill 3/32” pilot holes as specified. Attach screws to the driving bit for easier installation. Custom panel should be sized according to installation requirements. It is recommended to attach the custom panel before installing the dishwasher. Ensure the lower vent is not obstructed by the custom panel. Panel height must be between 29-13/16” and 30-1/4”. The custom panel must not weigh more than 20 lbs for optimal door balance. Install a custom handle onto the panel, aligning with adjacent drawer handles.
• Page 2: Couper le long du pointillé. Installation du panneau assemblé (suite). Percer un trou guide de 3/32 po à une profondeur de 2,4 mm (3/32 po). Instructions de gabarit pour panneau sur mesure épais de 19 mm (3/4 po) pour modèle de lave-vaisselle à intégré à commande supérieure. Important : pièces incluses. Attention : installer le panneau sur la porte du lave-vaisselle. Le panneau doit avoir entre au moins 29 13/16 po et 30 1/4 po de hauteur. Le panneau doit avoir au moins 23 3/4 po de largeur. Important : pour que la porte fonctionne bien, le panneau sur mesure ne doit pas peser plus de 9,07 kilos (20 livres). Important : si le gabarit n’est pas aligné correctement avec le panneau, le panneau peut frapper le coup de pied et empêcher l’ouverture complète de la porte.