MONOGRAM ZDT985SINII Dishwasher

1

2

Trim Around Dotted Line  

Trim Around Dotted Line  

10-13/16”  

10-13/16”  

STEP 6 INSTALL ASSEMBLED PANEL - (CONTINUED)  

3/4" Thick Custom Panel  

Template Instructions for  

Top Control Integrated  

Dishwasher Models  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

Due to location of screw holes and very limited space it will be very helpful to attach screws to the driving bit with  

tape to keep the screw from falling off inside the door while inserting down inside. Read and follow the steps below.  

1. Insert one of the sup-  

plied #8 x 5/8” truss head  

screws through a piece of  

masking tape.  

2. Insert a minimum 2” long bit  

into head and wrap tape  

around end of bit. (#1 square  

drive preferred)  

3. Use a bit extension with  

a max 3/8” diameter  

shank and a minimum  

2-3/4” length.  

The custom panel should be sized to your installation situation. See Step 1.  

It is highly recommended that the custom panel be attached before installing the dishwasher.  

Use this template to locate mounting screws and spacers on the custom panel.  

It is extremely important that the 2 screws are driven into the wood panel through the  

metal door assembly. This locks the vertical motion of the custom panel and if not secured  

the panel can come off the unit during door opening/closing causing personal injury and damage to the panel.  

IMPORTANT  

PARTS INCLUDED:  

CAUTION  

ꢀ

A custom handle must be installed onto the  

custom panel. Install the custom handle  

4-1/2” max. from the top of the panel.  

(4) Spacers  

(2) #8 x 5/8” Phillips truss head stainless steel screws  

(4) #8 x 7/8” Phillips truss head stainless steel wood screws  

(2) Heavy duty springs  

4. Carefully open the door because door will likely be unbalanced.  

Start insertion of driver at approximately 45˚ angle to clear the screw head past the hinge components, once the  

screw head is clear, rock the driver forward to a vertical position. Proceed to drive the screw. Repeat procedure for  

the opposite side.  

STEP 1 CUSTOM PANEL SIZE REQUIREMENTS  

HEIGHT  

ꢀ The bottom of the custom panel must not overhang the  

the bottom of the metal panel. Exceeding this will cause  

the custom panel to hit the toe kick and the door will not  

fully open. Any extra length of the custom panel must overhang  

at the top of the door.  

Panel height must be between 29-13/16" and  

30-1/4".  

Door shown fully open  

IMPORTANT: It is  

Custom Panel  

extremely important  

to make sure the lower  

vent is present and  

is not obstructed by  

the custom panel.  

29-13/16” Min.  

30-1/4” Max.  

Lower vent must be clear.  

Install custom panel above the  

lower vent.  

1

2

Custom  

Panel  

WIDTH  

Minimum 1/2” gap  

23-3/4”  

for clearance above  

Panel width must be 23-3/4".  

ꢀ If the panel width is less than  

23-3/4" it will not cover the  

dishwasher door frame.  

NOTICE: Do not overtighten screws.  

Excessive tightening of the screws  

could damage door edges.  

Drive screw through the hole  

in hinge bracket and door into  

the wood panel.  

top of metal dishwasher panel  

ꢀ If the panel height is more than 30-1/4", it will  

prevent the door from fitting under the cabinet.  

ꢀ If the panel height is less than 29-13/16" it will  

not cover the dishwasher door frame.  

Countertop  

3

1/2”  

min.  

IMPORTANT: To ensure optimum  

door balance performance, the  

custom panel must not weigh  

more than 20 lbs.  

Hinge  

Top of metal  

dishwasher panel  

Inner Door  

STEP 2 DRAW CENTERLINE  

Installed screw  

ꢀ Place the custom panel on a flat surface with appearance side down.  

ꢀ Locate the vertical center of the panel at the top.  

ꢀ Use a carpenters square to draw a centerline from top to bottom.  

STEP 7 INSTALL DOOR SPRINGS  

Side  

of  

Panel  

Side  

of  

Panel  

ꢀ Depending on the weight of the panel being used, additional springs may be needed to balance the door during  

operation. If only one spring is being attached to the cable, the spring hook should be inserted into the middle hole  

on the cable and the other end of the spring should be hooked over the lowest screw on the rear tub bracket as  

shown below:  

25-5/16”  

25-5/16”  

STEP 3 ALIGN TEMPLATE TO PANEL  

ꢀ Trim template on the dotted line along all sides.  

ꢀ Place template on the panel aligned with the bottom edge and the  

centerline. Use tape to hold in place.  

ꢀ If multiple springs are required on each side to balance the door, the spring hooks should be inserted into the top and  

bottom holes on the cable as shown below:  

IMPORTANT: If the template is not aligned properly with the  

panel, the panel may hit the toe kick and the door will not fully  

open. Longer panels should overhang at the top of the door.  

Make sure after installation, to maintain a minimum 1/8" gap to  

the countertop from the custom panel.  

Mark Center  

Screw Holes  

ꢀ Use an awl to mark the screw hole locations indicated on the  

template. Remove the template.  

ꢀ The bottom spring opposite end should be hooked over the lowest screw on the rear tub bracket. The top spring  

hooks into the first available hole above the screw in the same rear tub bracket. See illustrations below.  

ꢀ The following table may be used as a guideline regarding which springs to use, depending on the weight of panel  

being added. However, spring combinations may be adjusted based on personal preferences regarding door feel.  

STEP 4 INSTALL MOUNTING SCREWS AND SPACERS  

If the panel is less than 3/4" thick, shorter screws must be used.  

Use #8 x 3/4" screws for 1/2" thick panels (not supplied).  

ꢀ Use a 3/32" drill bit to drill pilot holes 3/32" deep in the marked  

locations. Make sure not to drill all the way through the panel.  

Note: The custom panel is secured to the dishwasher door with  

the spacers and screws provided. The 4 spacers will slip into the  

keyhole slots on the dishwasher door.  

ꢀ Drive the supplied #8 x 7/8” screws through the spacer and into  

the panel.  

ꢀ Install remaining spacers and screws as indicated in the marked  

locations.  

Note: For combinations requiring two different strength springs, the side used is unimportant and the table headings  

below are for reference only. For example, a panel weighing 8 lbs would require two (2) gray springs and one (1) blue  

spring. The gray springs may be installed on the left side and the blue spring on the right side, or the two gray springs  

may be installed on the right side and the blue spring on the left.  

Panel Weight (lbs) Left Side Springs Right Side Springs  

Spring Strength  

Gray  

Blue  

Light Duty  

Medium Duty  

Heavy Duty  

Screw  

Spacer  

0-5  

Blue  

Blue  

Blue  

5-10  

Gray x 2  

Blue x 2  

Blue x 2  

Black  

10-15  

15-20  

Black  

Black x 2  

STEP 5 INSTALL CUSTOM HANDLE  

Screws Must  

Be Countersunk  

Into Panel  

Side View  

ꢀ Close and latch the door.  

ꢀ Check door balance after custom panel is installed.  

If the door drops open too fast, you may swap any of  

the springs with the next heaviest spring as shown in  

the table.  

ꢀ Remove the rear screw-style leveling feet because of  

spring interference.  

A custom handle must be installed onto the panel before the panel is  

secured to the dishwasher door.  

ꢀ The handle should be installed so that it aligns with adjacent  

drawer handles, or 4-1/2" max. from the top of the panel. Secure  

the handle in the same manner as cabinet handles. Screws must be  

countersunk into the panel.  

4-1/2" Max.  

From Top  

of Panel  

Custom  

door  

panel  

Handle  

Custom  

Door Panel  

Custom  

Panel  

STEP 6 INSTALL ASSEMBLED PANEL  

ꢀ Secure the panel to the door by inserting the top and bottom  

spacers into the matching keyhole slots.  

ꢀ Make sure all 4 spacers engage the keyhole slots.  

ꢀ Press the panel against the door and push downward until the  

spacers are fully engaged into the keyhole slots. The panel should  

align evenly with the top and sides.  

Front View  

Make sure pulley cables  

are within pulley shoulders  

Dishwasher  

Door  

Spring  

hooked  

to screw  

inside leg  

Spacers  

Engage Keyhole  

Slots  

TIP: If the door does not open easily or falls too quickly, check  

spring cable routing. The cable is held in place by “shoulders”  

on the pulley. Check to be sure the cable has not slipped over  

the pulley shoulders.  

IMPORTANT: Adjust both balance springs to the same amount  

of tension to prevent excessive door twisting during use.  

10”  

10”  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

Drill 3/32"  

Pilot Hole  

3/32" Deep  

2-9/16”  

2-9/16”  

Pub no. 31-4000217-1  

Trim Around Dotted Line  

Trim Around Dotted Line  

05-22 GEA  

Align this with bottom edge of the door only. (Do not block vent exit).  

Bottom of Panel  

Bottom of Panel  

Do Not Block Vent Exit - See STEP 1  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	MONOGRAM ZDT985SINII Dishwasher
Make	MONOGRAM
Language	English
Filetype	PDF (Download)
File size	0.85 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• MONOGRAM

MONOGRAM ZDT985SINII Dishwasher Overview

Summary of Contents

• Page 1: Trim around dotted line. Step 6: Install assembled panel - (continued). Template instructions for top control integrated dishwasher models. Drill 3/32 pilot hole, 3/32 deep. It is highly recommended that the custom panel be attached before installing the dishwasher. It is extremely important that the 2 screws are driven into the wood panel through the metal door assembly. A custom handle must be installed onto the custom panel, 4-1/2” max. from the top of the panel. The bottom of the custom panel must not overhang the bottom of the metal panel. Panel height must be between 29-13/16 and 30-1/4. To ensure optimum door balance performance, the custom panel must not weigh more than 20 lbs.
• Page 2: Couper le long du pointillé. Percer un trou guide de 3/32 po à une profondeur de 2,4 mm (3/32 po). Installation du panneau assemblé. Il est fortement recommandé que le panneau de finition soit monté avant la mise en place du lave-vaisselle. Il est extrêmement important de visser les deux vis dans le panneau de bois à travers la porte métallique. Installer une poignée de finition sur le panneau de finition à moins de 11,5 cm (4-1/2 po) du haut du panneau. Le panneau doit avoir entre 29 13/16 po et 30 1/4 po de hauteur. Installer le panneau personnalisé au-dessus de la sortie d’air inférieure. Le panneau sur mesure ne doit pas peser plus de 9,07 kilos (20 livres). Vérifiez l'équilibre de la porte après avoir installé le panneau.