Home > Electrolux > Electrolux EIDW6105GS Dishwasher
Electrolux EIDW6105GS Dishwasher
3. If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Figure 8. An air
gap kit is available from a plumbing supply store. (If the drain
hose is installed through the floor, an air gap is necessary).
6. If levelers need to be removed, make sure that the floor is free of all
obstructions.
7. Carefully place dishwasher inside cabinet area such that is
centered in opening. Use caution when moving dishwasher to
preventdamagetocabinet, dishwasherandfloor.
Electric Shock Hazard
Disconnect electrical power at the fuse box
or circuit breaker box before beginning
installation.
4. If you connect to a disposer, the large end of drain hose will fit.
Figure 9(a). The knock out plug must be removed from
inside disposer inlet before making the final fit to drain
hose. See Figure 9(b).
8. Front of door needs to be even with the front of adjoining cabinets.
Frontlevelersshouldallow5/16”belowundersideofcountertop
to top of console.
Failure to follow this warning could result in
death or serious injury.
9. Check that dishwasher is level from side to side by placing a level
against the top front section of the tub. See Figure 5a.
Electric Shock Hazard
GroundingInstructions:
The dishwasher must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the appliance’s equipment grounding terminal
or lead. It is the consumer’s responsibility to contact a
qualified installer to make sure the electrical installation
conforms with the National Electrical Code and local codes
and ordinances.
Larger end
of hose
Cut for 5/8” connection.
Cut for 3/4” connection.
Cut Hazard
Metal color panels are sharp and should be
handled with care. Wear gloves to protect
hands.
fitsdisposer
inlet fitting.
Drain Hose
Figure 6a
Failure to follow this warning may result in
injury.
Figure 9(a)
Sink at Left
Do not connect the dishwasher to the power supply until the
appliance is permanently grounded.
Figure 5a
Figure 5b
4. Replace junction box cover.
All wiring connections must be enclosed in the junction box.
This unit has copper lead wires.
Installation Diagram
10. Check that the dishwasher is level from front to back by taking
out the lower rack, place level on the lower rack wheel support at
the bottom of the tub. See Figure 5b.
7
Joining aluminum building wire to stranded copper wire
should be done by a qualified electrician using materials
recognized by UL and local codes.
Drain Air Gap
Electric Shock Hazard
If all connections are correct, there are no leaks,
and unit runs properly, replace the kickplate
assembly before placing unit into operation.
11. Adjust levelers up or down until dishwasher is level.
Do not use an extension cord. Such use can result in fire,
electrical shock, or other personal injury.
Holes need to be pre-drilled using a #5 drill to secure unit.
Failure to follow these instructions could result in death or
serious injury.
Alternate
Drain
Through
Floor into
Separate
Trap
Failure to follow this warning could result in
electric shock.
12. Screw mounting brackets firmly to cabinet using screws provided
in literature packet. See Image Below.
check these items:
Finishing the Drain
Connection
8
q
Water and drain lines have no kinks and move freely
behindthedishwasher.
Remove
Knockout
Plug in
Sink at Right
2” Drain Hose Hole
q
q
q
Water supply is turned on.
Joints are free of leaks.
1. Review Figures 7, 8 and 9 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
yourneed.
Disposer
Wiring connections to junction box are tight all access
panels are secured back in place.
Figure 9(b)
q
q
q
Replace kickplate. See Figure 1
The drain hose loop must be at least 32” high from the floor
to insure proper drainage.
Figure 5c
Figure 5d
Drain hose is assembled to Drain Hose Connector.
All packing materials and consumer literature have
been removed from inside unit.
Entry Must be
Above Trap
5. If the cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
electrical or duct tape to avoid cutting drain hose.
13. Open and close dishwasher door slowly. Ensure that there is
clearance to the console. Adjust accordingly until door opens
and closes freely.
q
q
Dishwasher is level and securely fastened.
Open and close door to make sure it does not hit
surrounding cabinet or countertop.
6. Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor and
cabinets. IMPORTANT: Make sure there are no sharp bends
or kinks that might restrict drain flow.
q
Make sure that all wire ties are removed from the Adjustable
Rack Assembly, Versa Tray, Utility Tray and Silverware
Baskets.
“Y”
Branch
Tailpiece
Figure 6b
Finishing the Water and
Electrical Connection
6
7. Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT: Be careful not to overtighten clamp or
you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
check these items:
Sink at Right
2” Drain Hose Hole
Checking the Installation
9
q
Water and electrical lines are straight out in front of the
dishwasher.
Sink at Left
8. Be sure unit does not rest on drain hose. It should be free of
electrical components and door springs. Do not cut corrugated
drain hose. Pull excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
q
q
All four leg levelers are positioned properly.
Figure 7
Operate the machine through at
least one fill and pump-out,
checking the following items:
Property Damage
Cabinet Seals are positioned on the sides and top of the
dishwasher.
Do not solder within 6” of the water inlet valve. Damage to
the plastic parts in the valve may occur.
The drain hose loop must be at least 32” high from the floor
to insure proper drainage.
q
q
Cabinet Attachment Clips are attached to the cabinet on
both corners on top of the dishwasher.
Use care that no sealer, dirt, or other objects enter the valve.
Damage to the filter screen may occur.
q
On EWDW6505 press and hold SET Icon for 5 seconds
before first use. On EIDW6305 and EIDW6105 press and
hold down HI-TEMP Icon for 5 seconds before first use.
Replace Toe and Kickplate. Note: When replacing Toe
and Kickplate hand tighten screws.
Be sure the dishwasher is placed where the water inlet
valve will be kept from freezing. If the valve freezes, it may
rupture and flooding may occur.
2. If you connect to a sink drain, entry will need to be above trap.
A “Y” branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fittings and
instructions. See Figure 7.
q
q
At first fill, approximately 2 minutes make sure water
completely covers filter surface.
At pump-out: (pump-out is either when the cycle is
completed or canceled. refer to the Use and Care Manual
for Start/Cancel), make sure all water is pumped out.
Water Line
1. Flush water line before connecting it to water inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open water supply valve for
a few seconds and let water drain into a pan. Turn off water
supply at shut-off valve.
q
Check water connections again for leaks.
Air Gap
2. Route water line to water inlet valve as shown in Figure 4.
3. While firmly pulling water supply line into 90° elbow, tightly
connect water supply to water inlet valve. Supply line must be
free of kinks, scales, chips, and lubricants.
Right Side
Installation
7
4. Turn on water supply and check for leaks.
Electrical Supply
1. Remove junction box cover and pull house wiring into junction
box. See Figures Below.
Figure 8
2. Use a UL listed conduit connector (not included) at box to
stabilize wiring.
3. Connect incoming black lead to dishwasher’s black lead,
incoming white lead to dishwasher’s white lead and incoming
green lead to dishwasher’s green lead with wire nuts. (See
Grounding Instruction Warning). Wire nuts must be tight.
| General | Details |
|---|---|
| Name | Electrolux EIDW6105GS Dishwasher |
| Make | Electrolux |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.17 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Electrolux ESS87300UX Dishwasher
Electrolux EES48401L Dishwasher
Electrolux EFF9392SXA Dishwasher
Electrolux ESZ89400UX 800 SprayZone Dishwasher
Electrolux ESL2500RO Dishwasher
Electrolux KECA7400W Builtin Dishwasher
Electrolux TAPPAN Dishwasher
Electrolux KESC7320L Dishwasher
Electrolux EEC87400W Sliding Door Dishwasher
Electrolux EFC3862MS UltimateCare 300 Compact Dishwasher
BOSCH SMH8ZCX01E 60 cm Dishwasher
BOSCH SHP65CM6N Dishwasher
BOSCH SMH4ECX10E/01 Fully Dishwasher
MAINSTREET 541HTUC30 Undercounter Dishwasher
FOTILE SD2F-P3, SD2F-P3L In Sink Dishwasher
INFINITON DIW-G61N, DIW-G62W Dishwasher
lord D1000 Dishwasher
INDESIT W11667630 B Dishwasher
UNIQUE Classic Retro Dishwasher
Haier HDW13F0B1 Hygiene Dishwasher