Midea WQP4-2605 Tabletop Dishwasher

1

2

3

4

TROUBLESHOOTING TIPS  

Before calling for service  

Reviewing the charts on the following pages may save you from calling for service.  

Problem  

Possible Causes  

What To Do  

Dishwasher doesn't  

start  

Fuse blown, or the  

Replace fuse or reset circuit breaker.  

Remove any other appliances sharing  

the same circuit with the dishwasher.  

circuit break tripped.  

Power supply is not  

turned on.  

Make sure the dishwasher is turned  

on and the door is closed securely.  

Make sure the power cord is.  

properly plugged into the wall socket.  

Error code:E1;  

Check that the water supply is  

connected properly andthe water  

is turned on.  

Water pressure is low  

Door of dishwasher  

not properly closed.  

Make sure to close the door  

properly and latch it.  

Twisted or trapped  

drain hose.  

Check the drain hose.  

Water not pumped  

form dishwasher  

Filter clogged.  

Check coarse the filter.  

Kitchen sink clogged.  

Check the kitchen sink to make sure  

it is draining well.If the problem is  

the kitchen sink that is not draining,  

you may need a plumber rather than  

a serviceman for dishwashers.  

Use only the dedicated dishwasher  

detergent to avoid suds. If suds exist  

in the washer. Open the door for  

20-30 minutes to allow the foam to  

evaporate. If the foam still exists in  

the liner. Add 1.5L of water to the  

liner, close the dishwasher door and  

run a forced drain to drain it with the  

water. Repeat above operation until  

the foam is cleared.  

Suds in the tub  

Wrong detergent.  

36  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Midea WQP4-2605 Tabletop Dishwasher
Make	Midea
Language	English
Filetype	PDF (Download)
File size	0.67 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• Midea

Midea WQP4-2605 Tabletop Dishwasher Overview

Summary of Contents

• Page 1: Troubleshooting tips Before calling for service, reviewing the charts may save you from calling for service. Dishwasher doesn't start: Check if the fuse is blown or the circuit breaker is tripped. Ensure the power supply is turned on and the dishwasher is securely closed. Error code: E1; check that the water supply is connected properly and turned on. Make sure the door of the dishwasher is properly closed and latched. Check for a twisted or trapped drain hose. If water is not pumped from the dishwasher, check the filter and the kitchen sink for clogs. Use only dedicated dishwasher detergent to avoid suds. If suds exist, open the door for 20-30 minutes to allow the foam to evaporate. Add water to the liner and run a forced drain to clear the foam.
• Page 2: Problem: Stained tub interior Possible Causes: Detergent with colourant may have been used. What To Do: Make sure that the detergent has no colourant. Problem: White film on inside surface Possible Causes: Hard water minerals. What To Do: To clean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves. Never use any other cleaner than dishwasher detergent otherwise, it may cause foaming or suds. Problem: Rust stains on cutlery Possible Causes: The affected items are not corrosion resistant. What To Do: Avoid washing items that are not corrosion resistant in the dishwasher. Problem: A programme was not run after dishwasher salt was added Possible Causes: Traces of salt have gotten into the wash cycle. What To Do: Always run a wash programme without any crockery after adding salt. Problem: The lid of the softener is loose What To Do: Check the softener lid is secure. Problem: Knocking noise in the dishwasher Possible Causes: A spray arm is knocking against an item in a basket. What To Do: Interrupt the programme and rearrange the items which are obstructing the spray arm. Problem: Rattling noise in the dishwasher Possible Causes: Items of crockery are loose in the dishwasher. What To Do: Interrupt the programme and rearrange the items of crockery. Problem: Knocking noise in the water pipes Possible Causes: This may be caused by on-site installation or the cross-section of the piping. What To Do: This has no influence on the dishwasher function. If in doubt, contact a qualified plumber. Problem: The dishes are not clean Possible Causes: The dishes were not loaded correctly. What To Do: See notes in “Loading & unloading your dishwasher”. Problem: The programme was not powerful enough What To Do: Select a more intensive programme.
• Page 3: Problem: The dishes are not clean. Possible Causes: Not enough detergent was dispensed. What To Do: Use more detergent, or change your detergent. Items are blocking the movement of the spray arms. What To Do: Rearrange the items so that the spray can rotate freely. The filter combination is not clean or is not correctly fitted in the base of the wash cabinet. What To Do: Clean and/or fit the filter correctly. Clean the spray arm jets. Combination of soft water and too much detergent. What To Do: Use less detergent if you have soft water and select a shorter cycle to wash the glassware. Cloudiness on glassware. Possible Causes: Hard water area can cause limescale deposits. What To Do: Add more detergent. White spots appear on dishes and glasses. Possible Causes: Aluminium utensils have rubbed against dishes. What To Do: Use a mild abrasive cleaner to eliminate those marks. Black or grey marks on dishes. Problem: The dishes are not drying. Possible Causes: Improper loading. What To Do: Load the dishwasher as suggested in the directions. Dishes are removed too soon. What To Do: Do not empty your dishwasher immediately after washing. Open the door slightly to let the steam out.
• Page 4: Problem: The dishes are not drying. Possible causes include selecting the wrong program, which results in lower washing temperatures and decreased cleaning performance. To resolve this, choose a program with a long washing time. Using cutlery with a low-quality coating can also hinder water drainage, making these items unsuitable for dishwasher washing. Error codes will be displayed by the appliance to warn you of malfunctions. Common error codes include flow meter, drain valve, or pump failure, which should be repaired by a qualified worker. Not reaching the required temperature may indicate a heating tube or thermistor anomaly, also requiring professional repair. An overflow can occur if some element of the dishwasher leaks. Communication anomalies should be addressed by a qualified worker. If overflow occurs, turn off the main water supply before calling for service. Water in the base pan due to overfill or small leaks should be removed before restarting the dishwasher.