Whirlpool Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
The manufacturer ensures the availability of spare parts for at least 10 years after production date of this appliance.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt reservoir is empty (after refill the salt indicator may Refill reservoir with salt (for more information - see page 2).
Salt
indicator is lit
remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid dispenser is empty (after refill the rinse aid
indicator may remain lit for several wash cycles).
Rinse aid
indicator is lit
Refill dispenser with rinse aid (for more information - see page 2).
Insert the plug into the socket.
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly.
Power outage.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher door is not closed.
NaturalDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Close the door and press START/Pause button.
Cycle is interupted by door opening for > 4 sec.
It does not respond to commands. Display shows:
F9 or F12 and both On/Off
and START/Pause LEDs are blinking rapidly.
Switch off the appliance by pressing the ON/OFF button, switch it back on after
approximately one minute and restart the program. If problem persists, unplug the
appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows: F3
and both On/Off and
START/Pause LEDs
are blinking rapidly.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing
the DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without
detergent.
excessive noise.
An excessive amount of foam has been produced.
The dishes are not
clean.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher does
not fill the water.
Display shows:
and F6, both On/Off
and START/Pause
LEDs are blinking
rapidly.
No water in the water supply or the tap is closed.
The inlet hose is bent.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the
dishwasher and restart a new program.
Dishwasher finishes
the cycle prematurely.
Display shows: F15
and both On/Off and
START/Pause LEDs
are blinking rapidly.
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information can be
found by:
•
•
•
Using QR code on your product.
Visiting our website docs.whirlpool.eu/docs and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s
identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label. The label also
includes the model identifier that can be used to consult the portal of the registry at
400020009272
07/2024 jk - Xerox Fabriano
8
| General | Details |
|---|---|
| Name | Whirlpool Dishwasher |
| Make | Whirlpool |
| Language | English |
| Filetype | PDF (Download) |
| File size | 19.06 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Whirlpool 2B19 Dishwasher
Whirlpool WFO3O33PLAUS Standard Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool Thron Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WDF130PAHB Dishwasher
BOSCH SHX9PCM5N Benchmark Series Dishwasher
BOSCH SMS4EMW01E Dishwasher
GE APPLIANCES DT605PSMSS with Plastic Interior Dishwasher
BOSCH BSH CDN Service Dishwasher
HJC V31 Carbon Dishwasher
BOSCH SMI6ECS00E Dishwasher
ASKO D5233 Dishwasher
FISHER AND PAYKEL DD60SAX9 Dishwasher
FISHER AND PAYKEL DW60UC4X2 Contemporary Built Under Dishwasher
BOSCH SBD6YCX02E-46 Fully Integrated Dishwasher