Whirlpool WDFS3L5PIXAU Power Clean Maxi Tub 15 Place Setting Dishwasher
EN
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
The filter is clogged with food residues or lime-
scale.
The dishwasher
finishes the cycle
prematurely.
Display shows:
F8 E3
Check if the end of the drain hose is placed at the correct height (see INSTALLATION). Check for
siphoning into the home sewage system, and install a siphon breaker/air admittance valve if
necessary.
Drain hose positioned too low or siphoning into
the home sewage system.
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam is present.
Air in the water supply.
Check water supply for leaks or other issues letting air inside.
Make sure the rinse aid dispenser is filled (see FILLING THE RINSE AID DISPENSER). Multifunctional
tablets only will not provide as good drying effects as the actual use of liquid rinse aid.
Rinse aid is not present or the dosage is too low.
The dishes have been unloaded after the door
was opened automatically but before the actual better drying results, it is recommended to let the dishes sit inside the dishwasher with the door
Make sure the cycle has ended before starting to unload the dishes (see DAILY USE). For even
cycle end.
open for additional 15 minutes after the cycle ends.
The dishes are not
dried well.
If you notice puddles of water inside cavities of cups, mugs or bowls, try loading the dishes
(especially in the upper rack) providing more inclination to let larger amounts of water drip
down before drying starts.
The dishes are sitting too flat.
Please check in the PROGRAMS TABLE if the selected program is equipped in the drying phase.
A cycle without the drying phase may not deliver desired drying efficiency, so it is recommen-
ded to change cycle selection for the one that has the drying phase.
The selected cycle does not have the drying
phase.
The dishes are made of non-stick or plastic.
Rinse aid dosage is excessive.
Some water drops remaining on this type of material are normal.
Dishes and glasses
have blue streaks
or bluish tinges.
Adjust the dosage to a lower setting.
Refill the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
The salt reservoir is empty.
Dishes and glasses
are covered with
limescale or a whi-
tish film.
The water hardness setting is too low.
Increase the setting (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly
closed.
Check and close the salt reservoir cap.
The rinse aid reservoir is empty or the rinse aid
dosage is insufficient.
Refill the dispenser with rinse aid and check the dosage setting (for more information - see
FILLING THE RINSE AID DISPENSER).
The dishwasher
shows F8 E5
Valve is blocked or faulty.
Close the water tap, if possible. Do not switch off the power supply. Call the service.
Policy and standard documentation and additional product information can be found by:
•
•
•
Visiting our website: whirlpool.com.au
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s
identification plate.
IEC 436
:
6
| General | Details |
|---|---|
| Name | Whirlpool WDFS3L5PIXAU Power Clean Maxi Tub 15 Place Setting Dishwasher |
| Make | Whirlpool |
| Language | English |
| Filetype | PDF (Download) |
| File size | 6.2 MB |

Whirlpool 2B19 Dishwasher

Whirlpool WFO3O33PLAUS Standard Dishwasher

Whirlpool W11323304G Dishwasher

Whirlpool WH7IPC15BM60 Dishwasher

Whirlpool FINPUTSAD Dishwasher

Whirlpool W7U HS31 X Dishwasher

Whirlpool Thron Dishwasher

Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher

Whirlpool WRF540CWHZ Dishwasher

Whirlpool WDF130PAHB Dishwasher





















