ASKO DFI544D Dishwasher
Installation
Setup
•
The recess and connection dimensions are included in the separate installation instructions.
Check that all dimensions are correct before starting the installation. Note that the height of the
cover door can be adjusted to match other fittings.
•
•
•
Make sure the area on which the dishwasher is to be installed is firm. Adjust the adjustable feet
so that the dishwasher is level. Tighten the lock nuts.
If the dishwasher is built-in the surrounding furnishings must be resistant to any condensation
from the dishwasher.
Mount the protective film beneath the worktop and up around the edge. The function of the
protective film is to protect the worktop from moisture. (The protective film is in the enclosed
plastic bag.)
•
•
Check that the machine is installed such that the door opens freely, otherwise door lock
functionality may be disrupted.
Note that the door springs may need adjusting after a cover door has been fitted. Adjust the left
and right door springs equally until the door is evenly balanced.
Drainage connection
This dishwasher is suitable for installing in a raised recess (to attain an ergonomic working height).
This means that the dishwasher can be placed so that the drainage hose runs to a lower level than
the bottom of the dishwasher, such as by routing it directly to a floor drain. The dishwasher is fitted
with an integrated anti-siphon device to prevent the machine from being emptied of water during
the wash cycle.
The drainage hose can also be connected to a connection nipple on the sink unit's water trap. The
connection nipple must have an internal diameter of at least 14 mm.
The drainage hose may be extended by a maximum of 2.5 m (the total length of the drainage hose
must not exceed 4.5 m). Any joins and connecting pipes must have an internal diameter of at least
14 mm. However, the drainage hose should ideally be replaced with a new hose without joins.
No part of the drainage hose may be more than 950 mm above the bottom of the dishwasher.
Attach the drainage hose with a hose clamp. Ensure that the drainage hose has no kinks.
Connection to water supply
Use only the inlet hose supplied with the dishwasher. Do not re-use old or other spare hoses.
The supply pipe must be fitted with a water tap (stopcock). The water tap must be easily accessible,
so that the water can be shut off if the dishwasher has to be moved.
Once the installation is complete, turn on the water tap and allow the pressure to settle for a while.
Check that all connections are watertight.
Connection to cold water supply
Connect the dishwasher to the cold water supply if the building is heated using oil, electricity or gas.
Connection to hot water supply
Connect the dishwasher to the hot water supply (max. 70 °C) if the building is heated using an
energy-efficient means such as district heating, solar power or geothermal power. Choosing a hot
water connection reduces the dishwasher's energy consumption.
39
| General | Details |
|---|---|
| Name | ASKO DFI544D Dishwasher |
| Make | ASKO |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.13 MB |
(1 votes, average: 5.00 out of 5)
Loading...
ASKO DSD5444D Dishwasher
ASKO DFI8557MMXXL Dishwasher
ASKO DBI565IXXLS Logic Series 24 Dishwasher
ASKO DFI766UXXL.AU Dishwasher
ASKO DFI5558MKXXL Dishwasher
ASKO DFI777UXXL Dishwasher
ASKO D5636XXL Dishwasher
ASKO DFI7602MMXXL Dishwasher
ASKO DBI343ID.W.AU Dishwasher
ASKO D5233 Dishwasher
FISHER PAYKEL DD24DDFTB9_N Dishwasher
IKEA TORSBODA Dishwasher
BOSCH SMV4HBX40E-39 Dishwasher
BOSCH SMS4IKW51Q, XN Free Standing Dishwasher
INVENTUM VVW6008AW Dishwasher
Electrolux ESA12100SW Dishwasher
BOSCH SGI4HCS48E Dishwasher
Haier 500 Series Dishwasher
Whirlpool WIC 3C26 F Dishwasher
FISHER PAYKEL DD60D4HNX9 Dishwasher