BOSCH 9001164801 Dishwasher
Setting the Amount of Rinse Aid
The amount of rinse aid dispensed can be set from “r:00” to “r:06”.
To change the setting:
1
2
Press the [On/Off] button.
Hold down the “A” button (see page 15) and press [Start/Resume] until the display indicates
“H:0x”
(x can be any number).
3
4
5
Release both buttons.
Press the “A” button until the display shows “r:05”.
Press the “C” button to select the desired setting.
“r:00” = dispenser is OFF
“r:01” = lowest setting
“r:02” = low setting
“r:03” = medium setting
“r:04” = medium/high setting
“r:05” = high setting
“r:06” = highest setting
6
Press [Start/Resume] to save the setting.
Cycle Completion Signal
1
2
3
4
5
6
Open the door and press the [On/Off] button.
Hold down the “A” button (see page ꢀꢁ) and press [Start] until the display indicates “H:00”.
Release both buttons.
Press the “A” button until the display shows “b:02”.
Press the “C” button to increase or decrease the tone “b:00” = OFF and “b:03” = LOUDEST
Press [Start] to save setting and close the door.
Delay Start
You can delay the start of the cycle in one hour increments up to 24 hours.
To set delay start:
1
2
3
Press the [On/Off] button.
Press the [+] button until the display jumps to “h:01”.
Press the [+] or [-] button until the displayed time corresponds with your requirements.
h:01 = 1 hour delay
h:24 = 24 hour delay
4
Press [Start/Resume] to activate delay start.
To cancel delay start:
1
2
Press the [+] or [-] button until “h:00” is indicated on the digital display.
Press and hold [Start/Resume] for 3 seconds to cancel the cycle. You may now start a new cycle.
NOTE: Your dishwasher is protected against unintentional operation. If the appliance door remains open for more than 4 sec-
onds after pressing the [Start/Resume] button, the operation will be paused. Press the [Start/Resume] button again and close the
appliance door.
16
Auto Power Off
To save energy, the dishwasher is turned off 1 minute after the wash cycle ends. Auto Power Off can be
adjusted from P:00 to P:02.
To change the setting:
1
2
Press the [On/Off] button.
Hold down the “A” button (see page 15) and press [Start/Resume] until the display indicates
“H:0x” (x can be any number).
3
4
5
Release both buttons.
Press the “A” button until the display indicates “P:0x”.
Press the “C” button until the display corresponds with your requirements.
P:00 = dishwasher does not turn off automatically
P:01 = dishwasher turns off automatically after 1 minute
P:02 = dishwasher turns off automatically after 120 minutes (2 hours)
Press [Start/Resume] to save the setting.
6
InfoLight®
An LED illuminates the floor to indicate the unit is running. If the appliance is installed at eye-level, the
LED is not visible.
To change the setting:
1
2
Press the [On/Off] button.
Hold down the “A” button (see page 15) and press [Start/Resume] until the display indicates
“H:0x”.
(x can be any number)
3
4
5
Release both buttons.
Press the “A” button until the display shows “1:01”.
Press the “C” button to switch between “1:01” = ON and “1:00” = OFF and press [Start/Resume]
to save.
Aquastop® Leak Protection
Our AquaStop® system contains leaks through a precisely engineered tub and sensor system that works
with our solid molded base. If a leak has occurred, it shuts down operation and automatically pumps
out water to avoid contact with the floor. It works 24/7 and can turn itself on.
17
Care and Maintenance
A regular inspection and maintenance of your machine will help to prevent faults. This saves time and
prevents future problems.
Overall condition of the machine
Never use a steam cleaner to clean your dishwasher. The manufacturer is not responsible for any con-
sequential damage.
Regularly wipe the front of the appliance with a damp cloth - water and a small amount of liquid soap is
adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the
surfaces.
Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or chlorine based cleaners.
Use a stainless steel polish to seal and protect the surface.
Clean the outer edges of the inside door panel regularly to remove debris that may collect from normal
loading. If spots begin to appear on the stainless steel, make sure the rinse agent is full and functioning
properly.
WARNING
Use caution when removing parts for cleaning as some debris may be sharp.
Figure 12
Filters
The filter system consists of a coarse filter, a flat fine filter and a micro fil-
ter. The filters keep large foreign objects in the rinsing water away from the
pump. Foreign objects may occasionally block the filters.
Check the filters for residue by:
• Unscrew the filter cylinder as illustrated in Figures 12-13 and take out the
filter system.
• Remove any residue and clean filters under running water.
• Reinstall filter system in reverse sequence and ensure that the arrow
marks are facing each other after locking it into place.
Figure 13
Figure 14
Spray Arms
Check spray arms for grease and limescale deposits.
If you find such deposits:
ꢀ
ꢁ
• Fill detergent dispenser with detergent and start the appliance without
utensils in the cycle with the highest rinsing temperature (see wash cycle
information table).
• Clean the appliance with detergents/ appliance cleaners which are par-
ticularly suitable for use with dishwashers.
• Unscrew the spray arms and inspect as shown in Figure 14.
18
| General | Details |
|---|---|
| Name | BOSCH 9001164801 Dishwasher |
| Make | Bosch |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.93 MB |

BOSCH SMV6ZCX49E-39 Dishwasher

BOSCH SMI4HVS33E Dishwasher

BOSCH SRV2HKX39G Dishwasher

BOSCH SGS4HAW40G Dishwasher

BOSCH SGH4HVX32G Dishwasher

BOSCH SMS4ECI26E Dishwasher

BOSCH SMS6EDI02G Free-Standing Dishwasher

BOSCH SMS6EDW02G Free-Standing Dishwasher

BOSCH SMV4HTX27G Dishwasher

BOSCH SMV4HCX48E Dishwasher








































