FISHER AND PAYKEL DD24DI9 Dishwasher

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

DOUBLE DISHDRAWER™ DISHWASHER  

INTEGRATED  

DD24DHTI9, DD24DTI9, DD24DI9  

INSTALLATION GUIDE  

US CA  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	FISHER AND PAYKEL DD24DI9 Dishwasher
Make	FISHER and PAYKEL
Language	English
Filetype	PDF (Download)
File size	3.41 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• FISHER and PAYKEL

FISHER AND PAYKEL DD24DI9 Dishwasher Overview

Summary of Contents

• Page 1: Double Dishdrawer™ dishwasher Integrated Installation guide
• Page 2: Safety and warnings Electric shock hazard Failure to follow this advice may result in electrical shock or death. Fitting an integrated panel requires access to electrical service areas. Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Before fitting the front panel, the dishwasher must be disconnected from the power supply. Cut hazard Take care – panel edges are sharp. This appliance must be earthed to reduce the risk of electric shock. Tip hazard Before installing the DishDrawer™ Dishwasher, remove the house fuse or open the circuit breaker. The dishwasher must be completely enclosed at the time of installation.
• Page 3: Safety and warnings To reduce the risk of fire, injury to persons or damage when using the appliance, follow the important safety instructions listed below. Do not repair or replace any part of the appliance unless specifically recommended in this guide. Installation of this DishDrawer™ Dishwasher requires basic mechanical and electrical skills. Installation must comply with your local building and electricity regulations. This dishwasher is manufactured for indoor use only. Ensure all water connections are turned off. The DishDrawer™ Dishwasher must be installed to allow for future removal from the enclosure if service is required. The switched power outlet must be outside the dishwasher cavity, so that it is accessible after installation. Failure to install correctly could invalidate any warranty or liability claims. Save these instructions.
• Page 4: Tools and components Parts supplied Tools required Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage. Fisher & Paykel is not responsible for shipping damage. This video provides an overview of what is needed to install a DishDrawer™ Dishwasher. Installation should be undertaken by a Fisher & Paykel trained and supported service technician or qualified person. To access installation videos, scan the QR code with your smartphone or watch online. Toe kick cutting template (1) Toe kick mounting bracket
• Page 5: Product dimensions are provided for various models including DD24DTI9, DD24DI9, and DD24DHTI9. Overall height ranges from 32 1/4 to 34 5/8 inches. Overall width is 23 9/16 inches. Overall depth varies based on model specifications. Height of chassis is specified for each model. Depth of chassis is also provided. Ventilation gap between door panels is 5/16 inches. Minimum clearance between toe kick panel and floor is 1/2 inch. Height of feet ranges from 3/8 to 2 3/4 inches. Actual product dimensions may vary by 1/16 inch (2 mm).
• Page 6: Maximum weight of door panels must not exceed 20lbs (9kg) including handle. The panel should be adequately sealed to withstand moisture at 122°F (50°C) and 80% RH. The back and sides of the panel should be completely sealed with a waterproof vapor barrier to prevent damage. The back of the panel should be completely flush to maintain the seal between the panel and the rubber trim. Installation outside these specifications may result in condensation on cabinetry surfaces. Depending on the desired toe kick recess depth, the toe kick panel may need to be cut to clear the underside of the tub. A cutting template has been supplied with your DishDrawer and digital templates can be downloaded. Toe kick panel height can be determined using specified measurements. Minimum upper and lower door panel heights and widths are provided. Maximum extension of upper and lower panels and minimum clearances are specified.
• Page 7: Cabinetry Dimensions Clearances Connections can be located in an adjacent cabinet on either side of the DishDrawer. Minimum clearance to adjacent cupboard door is 1/16 inches. Minimum inside height is 32 1/4 inches. Minimum clearance to corner cupboard is 13 inches. Minimum overall depth is 28 3/8 inches. Recommended height of adjacent cabinetry is 30 inches. Height of toe kick area is 3 15/16 to 6 5/16 inches.
• Page 8: Plumbing & electrical considerations Your services can be installed to either the left-hand or right-hand side of the product in an adjacent cabinet. If the drain hoses supplied are not long enough to reach your services, you may purchase a Fisher & Paykel drain hose extension kit which will extend the drain hoses by 3.6m. Recommended water temperature: Hot (maximum 140°F (60°C)). Ensure water connection complies with local plumbing regulations. Water pressure for water softener models: max. 1 MPa (145 psi), min. 0.1 MPa (14.5 psi). Water pressure for non-water softener models: max. 1 MPa (145 psi), min. 0.03 MPa (4.3 psi). Drains will need to be separated to satisfy kosher requirements. We recommend confirming the acceptability with your local rabbi in respect to kosher installations. Minimum distance from floor to top of hose support is 29 1/2 inches to 34 3/4 inches. Electrical requirements: 120V, 60Hz, minimum current 8.7A.
• Page 9: You have the option to hard-wire your DishDrawer™ Dishwasher. To do this, we recommend removing the supplied power cord and doing the hardwiring installation as close to the cavity as possible. Ensure only copper conductors are used. Slide the terminal block cover sideways to unlock and hinge open to access the terminal block. Open the lower drawer and press both locking tabs back to release. Unscrew the Live, Neutral and Earth wires as shown. Lift the drawer off the runners and carefully set aside on a protected surface. Safely cut the cord from the inside and outside of the product to remove the cord. Fit a suitable cable clamp for the conduit through the metal knockout. Ensure wiring is routed through or under housing ribs.
• Page 10: Hard wiring (optional) Screw down the Live, Neutral and Earth wires correctly. Refit module cover before sliding the access cover back into place, ensuring the 2 clips shown are fully locked. Before refitting the drawers, ensure the hoses are not twisted and all latches are facing forward. Refit the drawer back onto the runners, ensure both runners are extended halfway before lowering the tub. Slide the runners forward to engage.
• Page 11: Preparation Service access We recommend locating the service holes on either side of the DishDrawer™ Dishwasher. If the holes are created through wood, ensure the edges are smooth and rounded. If the holes are created through metal, ensure the supplied edge protector is fitted. Ensure power cord is routed through a separate service hole to the hoses. Align the supplied moisture protection tape to the cabinetry as illustrated. Ensure this area is free of debris before carefully applying the tape to the surface. If securing via the drawer removal method, ensure the marked locations provide adequate support. If there are no side partitions, construct timber bracing to secure the fixings to. Select cabinetry securing method: Secure to cabinetry via brackets or secure via drawer removal.
• Page 12: Push the product into the cavity. Fit custom door panels. Remove both side pins from each drawer by pulling the pins out towards you. Secure all four side brackets to the DishDrawer™ Dishwasher, aligning bracket A with slot A and bracket B with slot B. Ensure the ends of the brackets are not pushed into the chassis. Loosen each foot by 1/2 a turn by lightly tilting the product and rotating each leg anticlockwise. Level the DishDrawer™ Dishwasher by carefully tipping it onto a protected surface. On the back of the upper panel, mark the centre and align the base of the upper bracket with the base of the panel. Rotate each leg anticlockwise to increase the height, and clockwise to decrease. Push the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them.
• Page 13: Fit custom door panels. Snap the bracket tab to remove. Re-insert the side pins on both drawers and push firmly to secure panels in place. Attach the Knock-to-Pause module to the panels as shown. Ensure the Knock-to-Pause modules are oriented correctly and are not in contact with the brackets before securing. Insert a Phillips screwdriver into the hole above each side pin and rotate to adjust the panel alignment. There is a maximum travel distance of 1/16 (2mm). To earth the panel bracket, connect the earth wire from the product to one of the tabs. Reconnect the Knock-to-Pause module to the UI 1 slot on the wash controller as shown. Ensure the minimum clearance gap of 5/16 (8mm) between panels is maintained after all adjustments have been made.
• Page 14: Secure to cabinetry via brackets (method A). Secure to cabinetry via drawer removal (method B). Open the lower drawer and press both locking tabs back to release. Partially open one of the drawers and remove the first screw cover from the trim moulding. Lift the drawer off the runners and carefully set aside on a protected surface. Pre-drilling a pilot hole may be required depending on the cabinetry material. Using your hand or the supplied hex socket and a screwdriver, level the DishDrawer™ Dishwasher as required. Rotate clockwise to increase the height of each leg and anticlockwise to lower. Secure to cabinetry via all four fixing locations in the chassis. Ensure sound insulation is replaced correctly.
• Page 15: Secure to cabinetry via drawer removal (method B). Measure toe kick height. Ensure hoses are not twisted and all latches are facing forward before refitting the drawers. The toe kick meets the bottom of the tub is the recommended cut-off point. Carefully score toe kick at desired height. Refit the drawer back onto the runners, ensuring both runners are extended halfway before lowering the tub. Slide the runners forward to engage. Snap excess and smooth edges. Snap both end tabs. Slide toe kick onto the mounting rails and secure.
• Page 16: Install custom toe kick If the depth of your toe kick recess is greater than 1 9/16 (40mm), the toe kick panel may need to be cut to one of the predetermined profiles. Refer to ‘custom panel dimensions’ for more information on determining which profile is suited to your install. Align the mounting bracket to the panel ensuring it is horizontally centred. Secure the mounting bracket to the panel using the supplied mounting screws. Carefully cut or router the panel to the desired profile using the cutting template as a guide. Slide toe kick onto the mounting rails and secure. Do not over tighten the screws. Ensure all panel edges are sealed to withstand moisture (122°F (50°C) @ 80% RH).
• Page 17: Plumbing & electrical connection Sink trap/waste tee installation Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to 'Plumbing & electrical considerations' for minimum install heights. Ensure the drain hose does not extend into water retained in the trap; an air gap is required to prevent waste water from siphoning back into the tub. Connect the inlet hose to tap and hand-tighten into place. Using a spanner or pliers, turn a further 180° to secure, avoiding over-tightening. Do not turn water supply on. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled. Plug product in.
• Page 18: Plumbing & electrical connection Install your Air Gap Kit to the benchtop. We recommend using a Dual Air Gap Kit. Refer to 'Plumbing & electrical connection' for minimum install heights. Thread wire clips onto the hoses before fitting them to the hose joiner. Unplug or drill out the waste tee before securing to sink trap or waste tee. Connect the inlet hose to tap and hand-tighten into place. Using a spanner or pliers, turn a further 180° to secure. Avoid over-tightening. The DishDrawer™ Dishwasher must be powered on for the flood protection feature to be enabled.
• Page 19: Installer checklist Check all parts are installed correctly and are secure. Ensure all electrical tests have been conducted in accordance with local regulations. Ensure all clearance gaps have been maintained. Turn on the power and water supplies, then open the drawer. You should hear a beep and see a program indicator light up on the control panel. Ensure DishDrawer™ Dishwasher is securely fastened to the cabinetry and drawer opens and closes freely with no resistance. Add three cups of water into the drawer. Ensure panel is fitted correctly to the DishDrawer™ Dishwasher. Navigate to RINSE and start the program. Check drainage connections for leaks. Ensure inlet hose has supplied rubber washer fitted, and that it’s tightened.
• Page 20: Troubleshooting No program indicator lights up when the drawer is opened. Ensure power is connected and is switched on. Auto power-on may need to be activated. Water supply fault. Ensure the water supply is turned on. Press once to stop the beeping, then again to clear the fault. Drawer doesn’t close properly. Ensure nothing is obstructing the drawer from closing such as hoses or drawer latches. Water appears around water supply and drain connections. Check the drainage hose and connection for any blockages. Ensure the spigot is drilled out. Product is tipping. Ensure the product is secured to the cabinetry. Front panels are misaligned to surrounding cabinetry. Check the cabinetry is square. Check and relevel product. If a problem occurs that is not listed, refer to your user guide for additional troubleshooting.