GAGGENAU DF480161F Dishwasher
Dishwasher Connectionꢀen-us
some detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water supply
pressure must be between 7.25 - 145 psi (0.5 - 10 bar).
3. After all connections are made, turn on the hot water
and check for leaks.
5.2ꢀInstalling the Drain Connection
WARNING
The drain hose must be installed with either a high loop or
an air gap.
Scalding Hazard
▶ Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
NOTICE:
Proper drain hose installation
▶ The dishwasher drain hose must be installed with a
portion of it at least 33” (84 cm) off the floor; otherwise
the dishwasher may not drain properly.
Remove garbage disposal plug
NOTICE:
Soldering plumbing lines
▶ If the dishwasher drain hose will be connected to a
garbage disposal connection, first remove the plug from
the disposal connection.
▶ Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
▶ Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
Note
Important notes for drain connection:
¡ If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
¡ The drain hose length can be extended if necessary.
Use kit #SGZ1010UC. The maximum length of the drain
hose, including the hose leading to the air gap, is 150″
(380 cm).
¡ You may attach the hose clip to the inside of the
adjacent cabinet to hang the drain hose (screws are not
supplied) in place of using a nonmetallic tie as pictured
in the next illustrations. Do not exceed 43” in drain hose
height.
Note
Important notes for water connection:
¡ If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡ Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡ If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
¡ Always use appropriate seals when making plumbing
connections.
1. Flush the incoming water line for approximately 1
minute to clear any foreign material.
2. Connect the dishwasher water supply line to the water
shut off valve, using the adaptor if included with your
model. Turn by hand and do not over tighten.
‒ Install a shut off valve if one isn’t already in the
supply line.
‒ Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
1. Place hose clamp around end of drain hose BEFORE
connecting to the plumbing.
17
| General | Details |
|---|---|
| Name | GAGGENAU DF480161F Dishwasher |
| Make | Gaggenau |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.56 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Gaggenau DF264101 Dishwasher
GAGGENAU DF271101F Dishwasher
GAGGENAU DF481100 Dishwasher
GAGGENAU 400 Dishwasher
Gaggenau 9001923384 B Dishwasher
GAGGENAU DF261101 Dishwasher
Gaggenau DF211700 Dishwasher
GAGGENAU DF480701F Dishwasher
GAGGENAU DF481100F 400 Series Dishwasher
GAGGENAU 11029813 Fully- Dishwasher
GAGGENAU DF481100F 400 Series Dishwasher
SOLT GGSDW6013W Dishwasher
Hisense HV642C60 Dishwasher
BOSCH SHP78CM4N Pocket Handle Dishwasher
BOSCH SMS4HCW19E Dishwasher
FISHER AND PAYKEL DD60SCHW9 Contemporary Dishwasher
MONOGRAM ZDT985SINII Dishwasher
INVENTUM IVW6015A Dishwasher
BOSCH SMS4IKI51Q Free Standing Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Integrated Dishwasher