INSIGNIA NS-DWRF2SS3 Front Dishwasher
Front Control Dishwasher
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
The rinse aid light is on The rinse aid level is low.
Add rinse aid.
The dishwasher runs
too long
The dishwasher is connected to a cold Make sure that the dishwasher is connected to a hot
water supply. water supply. If not, change the water supply to a hot
water source.
The cycle time varies, depending on the When heavy soil is detected, the wash times will be
soil level of the dishes.
longer.
Some cycles and options take longer.
The water pressure is too low.
This is normal.
The dishes are not
clean enough
Make sure that the water pressure is above 20 psi.
Use your dishwasher when water demand is low.
The inlet water temperature is too low. Make sure that the dishwasher is connected to a hot
water supply. If not, change the water supply to a hot
water source.
Use your dishwasher when hot water demand is low.
The water temperature may be too low Run the hot water in the sink for 30 seconds or until
at the start of the wash cycle.
the water runs hot, then start the dishwasher.
Dishes are too close together.
Reload the dishwasher as shown in Preparing and
loading dishes on page 7.
Improper use of detergent.
Add detergent depending on the water hardness
and washing cycle you choose. Use fresh detergent.
The selected cycle is not suitable for the Choose a different cycle with a longer washing time.
soil level on the dishes.
The spray arms are blocked.
Make sure that the spray arms are not blocked and
are free to rotate.
The dishes are not dry The rinse aid dispenser is empty or the Fill the rinse aid dispenser.
enough
setting is too low.
Increase the rinse aid setting.
Dishes are loaded improperly.
Reload the dishwasher as shown in Loading the
upper rack on page 8 and Loading the bottom rack
on page 9.
The cycle you chose did not include
drying.
Choose a cycle with drying.
Spots and filming on
dishes
Water hardness is too high
For extremely hard water, install a water softener.
Dishes are loaded improperly.
Reload the dishwasher as shown in Loading the
upper rack on page 8 and Loading the bottom rack
on page 9.
Old or damp rinse aid powder is used. Use fresh, liquid rinse aid.
The rinse aid dispenser is empty or the Fill the rinse aid dispenser.
setting is too low.
Increase the rinse aid setting.
Etching
Too much detergent being used.
Use less detergent if you have soft water.
Lower the inlet water temperature.
The inlet water temperature exceeds
150° F (65.6° C).
Detergent left in
dispenser cup
Detergent may be too old.
The spray arm is blocked.
Use fresh detergent.
When you load the dishes, make sure that the spray
arms are not blocked.
The detergent Improper operation of the detergent
dispenser will not close cover.
Add detergent and rinse aid only as indicated in this
manual. See Filling the detergent dispenser on page
10.
Water remains in the
dishwasher.
The previous cycle has not finished or
has been interrupted.
Make sure that the current cycle is finished.
17
| General | Details |
|---|---|
| Name | INSIGNIA NS-DWRF2SS3 Front Dishwasher |
| Make | Insignia |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.6 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INSIGNIA NS-DWF2SS3 Dishwasher
INSIGNIA NS-DWH2SS8 Dishwasher
INSIGNIA NS-DWH1SS9 Dishwasher
INSIGNIA NS-DWR3SS1 Dishwasher
FISHER and PAYKEL DD60ST4NB9 Contemporary Tall Dishwasher
FISHER AND PAYKEL DW24UT2I2 Tall Dishwasher
GAGGENAU DF481100F 400 Series Dishwasher
BOSCH SMP6HCS01A 6 Built Under Dishwasher
SAMSUNG DW80CG545 Dishwasher
beko BDFN15430G Electrical Household Dishwasher
BOSCH SRV2HKX39G Dishwasher
BOSCH SMV4EVX14E Dishwasher
Whirlpool W0I D741A S Fully Dishwasher
FRIGIDAIRE DWU-22J Dishwasher