INSIGNIA NS-DWRF2SS3 Front Dishwasher
Troubleshooting
Refer to this table to correct minor issues before calling for service.
Error codes
CODE
MEANING
POSSIBLE CAUSE
POSSIBLE SOLUTION
Rinse light blinks and your The water flow is
• Water faucet is not opened
• Water pressure is too low
• The drain hose is plugged
• Other (parts failure of inlet or
drain system)
• Make sure that the water is
turned on to the dishwasher
• Make sure that the water
pressure is 20~100 psi
• Check the drain hose
• Contact Customer Service
dishwasher beeps for 15
seconds
insufficient or the
water pressure is
too high
Express and rinse lights
blink and your dishwasher
beeps for 15 seconds
Abnormal heating
Overflow or leak
• Contact Customer Service
Heavy light blinks and
your dishwasher beeps for sensor activated
15 seconds
• A leak
• Too much water in the tub
• Turn off water to your
dishwasher, then check the
filter system for blockage.
Unblock if necessary.
• If there is no water in the tub,
contact Customer Service
Heavy and express lights
blinks and your
dishwasher beeps for 15
seconds
• Contact Customer Service
• Contact Customer Service
Heavy, express, and rinse
lights blink and your
dishwasher beeps for 15
seconds
Normal, heavy, and rinse Communication
• The display board can’t receive • Contact Customer Service
or the main board can’t send a
signal for longer than 20
lights blink and your
dishwasher beeps for 15
seconds
exception or issue
seconds
Note: After resolving an error code issue, cycle the power on the dishwasher using the power button on the dishwasher control panel.
If the error code persists, you may need to cycle the power to the dishwasher by resetting the circuit breaker that powers the
dishwasher.
Important:
• If an overflow occurs, turn off the main water supply before calling for service.
• If there is water in the base pan because of an overfill or small leak, the water should be removed before restarting the dishwasher.
PROBLEM
POSSIBLE CAUSE
POSSIBLE SOLUTION
The dishwasher won’t The door may not be closed properly.
start
Make sure that the door is closed and latched.
The power is off or not connected.
Make sure that the power is connected and turned
on. If your home has a wall switch above the
dishwasher that powers the dishwasher outlet, make
sure that the wall switch is in the On position.
The delay start option is selected.
The child lock is activated.
Refer to the “11- Delay” section on page 7.
Deactivate the child lock. Refer to the “Child lock”
section under Cycles on page 6.
The wall switch is not turned on.
Some dishwashers have a wall switch mounted
above the counter that controls the dishwasher.
Make sure that this switch is turned on.
The dishwasher beeps This is normal and indicates that the
eight times at the end wash cycle is complete.
of the cycle
16
| General | Details |
|---|---|
| Name | INSIGNIA NS-DWRF2SS3 Front Dishwasher |
| Make | Insignia |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.6 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INSIGNIA NS-DWF2SS3 Dishwasher
INSIGNIA NS-DWH2SS8 Dishwasher
INSIGNIA NS-DWH1SS9 Dishwasher
INSIGNIA NS-DWR3SS1 Dishwasher
BOSCH SHPM65W55N Dishwasher
BOSCH SMH4ECX14E Dishwasher
FISHER AND PAYKEL DW60FC4X2 Sanitise Dishwasher
Bauknecht 3O35 PF Dishwasher
BOSCH SMS26DI01B Dishwasher
FISHER PAYKEL DD60SCTW9 Sanitise Single DishDrawer Dishwasher
PKM GSP9-6TI Dishwasher
BOSCH SHP65CM5N Dishwasher
FISHER and PAYKEL DW60UT4HI2 Tall Dishwasher
smeg DI13M2 Dishwasher