CAFE CDD220P2WS1 Smart Drawer Dishwasher

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

TM  

Installation Instructions  

Dishwasher Drawer  

If you have questions, visit our website at: cafeappliances.com  

BEFORE YOU BEGIN - Read these instructions completely and carefully.  

FOR YOUR SAFETY  

Read and observe all WARNINGS and CAUTIONS shown throughout these  

instructions.  

WARNING  

IMPORTANT – Observe all governing codes and ordinances.  

Ŷ

Ŷ

To reduce the risk of electric shock, fire, or injury to persons, the installer must  

ensure that the dishwasher is completely enclosed at the time of installation.  

ŶꢀNꢀ ote to Installer – Be sure to leave these instructions for the consumer’s and  

local inspector’s use.  

FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before  

beginning installation. Do not use an extension cord or adapter plug with this  

appliance.  

ŶꢀNꢀ ote to Consumer – Keep these instructions with your Owner’s Manual for  

future reference.  

ŶꢀSꢀ kill Level – Installation of this dishwasher requires basic mechanical, electrical  

and plumbing skills. Proper installation is the responsibility of the installer.  

Product failure due to improper installation is not covered under the GE  

Appliances Warranty. See Warranty information.  

Ŷ

Ŷ

Ŷ

The improper connection of the equipment grounding conductor can result in a  

risk of electric shock. Check with a qualified electrician or service representative  

if you are in doubt that the appliance is properly grounded.  

If house wiring is not 2-wire with ground, a ground must be provided by the installer.  

When house wiring is aluminum, be sure to use UL-Listed anti-oxidant  

compound and aluminum-to-copper connectors.  

ŶꢀCꢀ ompletion Time – 1 to 3 Hours. New installations require more time than  

replacement installations.  

IMPORTANT – The dishwasher MUST be installed to allow for future removal from  

the enclosure if service is required.  

To reduce the risk of electric shock, fire, or injury to persons, the installer should  

check to ensure that wires are not pinched or damaged, the house wiring is attached  

to the dishwasher through a strain relief, and all electrical connections made at  

the time of install are contained inside of the terminal block cover.  

For models equipped with power cord: Do not modify the plug provided  

with the appliance; if it will not fit the outlet, have a proper outlet installed by a  

qualified technician.  

Care should be exercised when the appliance is installed or removed, to reduce the  

likelihood of damage to the power supply cord.  

If you received a damaged dishwasher, you should immediately contact your dealer  

or builder.  

Your dishwasher is a water heating appliance.  

Ŷ

CAUTION  

While performing installations described in this booklet, gloves, safety glasses  

or goggles should be worn.  

READ CAREFULLY  

KEEP THESE INSTRUCTIONS  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	CAFE CDD220P2WS1 Smart Drawer Dishwasher
Make	Cafe
Language	English
Filetype	PDF (Download)
File size	3.1 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• Cafe

CAFE CDD220P2WS1 Smart Drawer Dishwasher Overview

Summary of Contents

• Page 1: Installation instructions for the dishwasher drawer are provided. Read these instructions completely and carefully before beginning. Observe all warnings and cautions throughout the instructions for safety. Ensure the dishwasher is completely enclosed at the time of installation to reduce the risk of electric shock, fire, or injury. Leave these instructions for the consumer’s and local inspector’s use. Remove house fuse or open circuit breaker before beginning installation. Installation requires basic mechanical, electrical, and plumbing skills. Improper installation is not covered under the warranty. The dishwasher must be installed to allow for future removal if service is required. Wear gloves and safety glasses or goggles while performing installations.
• Page 2: Precauciones en Español Antes de comenzar, lea estas instrucciones en su totalidad y atentamente. Para su seguridad, lea y cumpla con todas las advertencias y precauciones que figuran en estas instrucciones. Cumpla con todos los códigos y ordenanzas gubernamentales. Para reducir el riesgo de descarga eléctrica, incendio o lesiones a personas, el instalador debe asegurarse de que el lavaplatos esté completamente cerrado en el momento de la instalación. Nota para el instalador: Asegúrese de entregar estas instrucciones al consumidor y al inspector local. Para seguridad personal: Quite el fusible o abra el interruptor de circuitos antes de comenzar la instalación. La instalación de este lavavajillas requiere un nivel básico de habilidades mecánicas, eléctricas y de plomería. El lavavajillas debe ser instalado para permitir el retiro futuro de su ubicación, si se requiere realizar el servicio técnico. Se deberá tener cuidado cuando el electrodoméstico sea instalado o retirado, a fin de reducir la posibilidad de daños sobre el cable de suministro eléctrico. Al realizar las instalaciones descritas en este folleto, se deben usar guantes, gafas de seguridad o gafas protectoras.
• Page 3: Installation preparation for the Dishwasher Drawer includes an overview of the installation process. Tools needed for installation are gloves, flashlight, safety glasses, Phillips-head screwdriver, flat head screwdriver, pliers, drill and bits, measuring tape, carpenter’s square, and level. Parts supplied in the installation package include a drain hose, support, drain hose joiner, wire clips, clamp, and side mounting bracket kit. Optional components include top mounting brackets, Phillips screws, bottom fixing screws with metal washers, rubber washer for inlet hose, moisture protection tape, and hexagonal socket for feet adjustment. If the supplied drain hoses are insufficient, a Drain Hose Extension Kit is available to extend the hoses by 11’ 10”. Consider recycling options for appliance packaging material.
• Page 4: Installation preparation involves ensuring proper electrical wiring. Improper connection of the equipment grounding conductor can result in a risk of electric shock. Remove house fuse or open circuit breaker before beginning installation for personal safety. Do not use an extension cord or adapter plug with this appliance. Electrical requirements include a 120V, 60Hz, AC-only, 15-ampere or 20-ampere, fused electrical supply. Wiring must be 2 wire with ground and rated for 75°C (167°F). If the electrical supply does not meet the requirements, call a licensed electrician before proceeding. The appliance must be connected to a grounded metal, permanent wiring system. Grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. The appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug.
• Page 5: Installation preparation Power cord or hardwire option We recommend the use of the power cord. If using the power cord option, skip steps 1-4. If you elect to hardwire the dishwasher drawer, follow steps 1-4 and then continue with the rest of the installation instructions. In preparation of removing the dishwasher drawer, place a sturdy box nearby to rest the drawer on after it is removed. Cover the box with a towel to provide a protective surface for the drawer to rest on. With a flat-bladed screwdriver, push in the clips and slide out the access cover. Unscrew the electronics module cover and carefully pull out the electronics module. Only unscrew the live and neutral terminals 2 turns. The ground requires the screw to be removed. Do not move or rest the drawer too far to prevent strain on its rear connectors. Press the release tabs in on both sides and push them back to release the drawer from its runners.
• Page 6: Installation preparation involves several important steps for hard wiring. If house wiring is not 2-wire with ground, a ground must be provided by the installer. When using aluminum wiring, it is essential to use UL-Listed anti-oxidant compound and aluminum-to-copper connectors. Fit a suitable cable clamp for the conduit through the metal knockout. Ensure wiring is routed through or under housing ribs. Screw down the Live, Neutral, and Ground wires correctly. Push the plastic harness cover back over to clip it into place. Refit the electronics module back into position, being careful of wiring. Ensure house wires are routed underneath all other harness wiring from the electronics module. Use copper conductors only for connections.
• Page 7: Installation preparation involves optional hard wiring prior to installation. Refit the drawer onto the runners and close it, skipping this step if using the power cord. Lift or rotate counter-clockwise the drawer back onto the drawer runners on either side. Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Pull the release tabs forward on both sides, ensuring they are fully pulled forward and click into place.
• Page 8: Installation preparation Product dimensions Overall height of product: 17-13/16” (453) Overall width of product Overall depth of product (excluding handle) Depth of chassis (to back of front drawer panel) Depth of drawer front panel (including handle) Height of drawer front panel Height of chassis Ventilation gap between drawer front panels Maximum extension of drawer: 5/16” (8)
• Page 9: Installation preparation involves understanding cabinetry dimensions. Minimum clearances from adjacent cabinetry are essential for proper installation. The inside height of the cavity should be a minimum of 17-15/16” (456 mm). The inside width of the cavity should be 23-5/8” (600 mm). The inside depth of the cavity should be a minimum of 22-13/16” (580 mm). A minimum clearance of 1/2” (13 mm) from a corner cabinet is required. A minimum clearance of 1/16” (2 mm) to adjacent cabinet doors is necessary. Bracket slots should be considered during installation. Understanding these dimensions ensures a proper fit for cabinetry. Plan accordingly to meet these specifications for successful installation.
• Page 10: Installation preparation includes cavity preparation and countertop considerations. Moisture protection tape must be applied. The recommended hot water temperature is a maximum of 140°F (60°C). A supplied hose connects to a compression fitting. Marks indicate formed bracket screw locations for securing by drawer removal. If there is no side partition, timber bracing can be constructed for securing. Water pressure should be a maximum of 1 MPa (145 psi) and a minimum of 0.03 MPa (4.3 psi). Incorrect placement of the hole will result in damage to hoses. The power outlet must be located in a cabinet adjacent to the dishwasher cavity. If the hole is through wood, ensure its edges are smooth and rounded.
• Page 11: Installation preparation includes maximum distance of hoses and cord from chassis edge. The left-hand side has drain hoses measuring 70-1/2” (1800mm) and inlet hose measuring 49” (1250mm). The right-hand side has drain hoses measuring 78-1/2” (2000mm) and inlet hose measuring 64-3/4” (1650mm). Power cord specifications are also provided.
• Page 12: Installation instructions provide guidance on securing the unit without removing the dishwasher drawer. Choose the installation method that is most suitable for your cabinetry. Recommended method (A) is for frameless cabinetry only. Attach side mounting brackets securely into their slots using a flat-bladed screwdriver. Pull hoses through and push the unit into the cavity. Optional: Attach the two top mounting brackets before sliding the product into the cavity. Ensure the ends of the brackets are not pushed down into the chassis when fitting. Initially level the product before proceeding with installation. If the product cannot be pushed in far enough, rearrange hoses and cord to avoid excessive force. Ensure hoses and cord do not get kinked or twisted during installation.
• Page 13: Installation instructions provide guidance for securing cabinetry. Option A is recommended for installation. Secure to the side cabinetry or above cabinetry as needed. Open the drawer halfway for proper access. Top mounting brackets can bend upwards a maximum of 3/8” (10 mm). Replace the grey rubber plug back into the trim moulding. Ensure the trim seal is facing forward. Use a flat bladed screwdriver to pry the grey rubber plug out. Use a small Phillips screwdriver to secure the side mounting bracket. Repeat the process for all four brackets without damaging the rubber trim seal.
• Page 14: Installation instructions provide guidance on securing the dishwasher drawer. Choose which installation method is most suitable for your cabinetry. Alternate method (B) involves removing the dishwasher drawer. Lift the drawer off its runners and place it upright on a covered sturdy box. Prepare a sturdy box nearby to rest the drawer on after removal. Optional: Attach the two top mounting brackets, ensuring the ends are not pushed down into the chassis. Initially level the product by pulling the dishwasher drawer out until it stops. Do not move or rest the drawer too far to prevent strain on its rear connectors. If the product cannot be pushed in far enough, rearrange hoses and cord. Ensure hoses and cord do not get kinked or twisted while pushing the product in.
• Page 15: Installation instructions outline the steps for securing the product to cabinetry. The product has three pairs of fixing points. Ensure the sound insulation is repositioned correctly. Use 1-1/2” (38mm) fixing screws and washers for the bottom fixing holes. Use 5/8” (16mm) screws for the formed brackets on either side of the chassis. Refit the drawer onto the runners on both sides. Ensure the hoses are not twisted before refitting the drawer. Latches at the rear of each drawer runner should face forward. Pull the release tabs forward on both sides to secure the drawer. Ensure the tabs are fully pulled forward and click into place.
• Page 16: Installation instructions provide three different plumbing and drainage options. Drainage option 1 involves using a dishwasher and a 1-1/2” (38 mm) standpipe. The drain hose should be secured to the back wall at the correct height. If space is limited, the maximum height for fixing is 4-3/4” (120 mm). It is important to install the drain hose as close to the underside of the countertop as possible to prevent waste from re-entering. The drain hose must not extend into water retained in the trap; an air gap is necessary to avoid siphoning. Ensure that the drain connection complies with local plumbing regulations. Refer to the “Connect inlet hose to hot water” step for additional guidance.
• Page 17: Installation instructions provide guidance on plumbing and drainage options. There are three different plumbing and drainage options to choose from. Drainage option 2 involves using an air gap with a drain hose joiner for the dishwasher. It is recommended to use a commercially available air gap kit. When installing two single drawers, separate draining for each drawer is provided. This setup eliminates possible cross draining problems. The maximum height to the top of the air gap is 37-3/8” (950 mm). Ensure that the drain connection complies with local plumbing regulations. Secure the drain hose to the air gap. Refer to the Connect inlet hose to hot water step for additional instructions.
• Page 18: Installation instructions provide guidance on plumbing and drainage options. There are three different plumbing and drainage options to choose from. Drainage option 3 involves using a drain hose joiner onto the sink trap or waste tee. A supplied drain hose joiner is included to suit the installation. The drain hose should be screwed securely. Support the installation to the back wall at the correct height. If space is limited, push the hose through the drain hose support to the required height. Ensure the drain hose is routed straight to prevent waste water accumulation. It is important to comply with local plumbing regulations for the drain connection. Do not shorten the inlet hose during installation.
• Page 19: Installation instructions include connecting water and switching the dishwasher on. Ensure the supplied rubber washer is fitted inside the coupling. Check for a kinked drain hose or blocked waste connection if excessive water remains above the filter plate. Verify that water is connected and turned on if there is no water supply. Continuous beeping indicates a fault; refer to the Owner’s Manual for instructions. Ensure power is connected and switched on if no program indicator lights up. Check connections and hoses for leaks around water supply and drainage connections. Secure the product to the cabinetry if it is tipping. Re-level the product and check cabinetry alignment if front panels are misaligned. Ensure nothing obstructs the drawer from closing properly.
• Page 20: Installation instructions include a final checklist to be completed by the installer. Check all parts are installed and ensure power and water supplies are turned on. You should hear a beep and see a program indicator light up on the internal control panel. Ensure all panels and parts are secure and that final electrical tests comply with local regulations. Check that spray arms are correctly mounted and free to rotate. Ensure the product is level, securely fastened to cabinetry, and opens and closes freely. Verify that the inlet hose to the water supply has a rubber washer fitted and is tightened properly. Ensure any knockouts or plugs in the drain connection have been removed and the connection is made. Add three cups of water into the drawer and press the program button to start the program. Check the water supply has shut off correctly and inspect the drainage connection for leaks.