Home > Electrolux > Electrolux ESF6768KXA Dishwasher
Electrolux ESF6768KXA Dishwasher
29
Water drain hose
WARNING
If you connect the water
drain hose to a trap spigot
under the sink, remove the
plastic membrane. If you
do not remove the entire
membrane, remaining food
can cause blockage in
Electrical Connection
Remove
entire internal
membrane
The plug of your machine should be connected to an
earthed outlet that supplies suitable voltage and current.
If there is no earthing installation, have a competent
electrician carry out an earthing installation. In case of
usage without earthing installed, our company will not be
responsible for any loss of usage that might occur.
the drain hose spigot. Ensure a hose clamp is used to
secure the hose to the spigot.
The indoor fuse current value should be 10-16 A.
Water drain hose
Your machine is designed for 220-240 V. The machine
should not be plugged in during installation.
The water drain hose can
be connected either directly
to the water drain hole or to
the sink outlet spigot. Using
a hose hook (if available),
the water can be drained
directly into the sink by
•
•
•
Always use the molded plug supplied with your
machine.
Running at low voltage will cause a decline in
washing quality.
The machine’s electrical cable should be replaced
by an authorised service or an authorised electrician
only. Failure to do so may lead to accidents.
positioning the hose hook
over the edge of the sink.
•
For safety purposes, always make sure to
disconnect the plug when a wash program
is finished.
This connection should be at a minimum of 50cm
and at a maximum of 110cm above the base of the
dishwasher.
•
•
In order not to cause an electric shock, do not
unplug when your hands are wet.
When disconnecting your machine from the mains
supply, always pull from the plug. Never pull the
cord itself.
WARNING
Maximum drain hose length is 4m. Longer hose
length will prevent correct draining,
and result in poor wash performance.
Fitting the machine undercounter
If you wish to fit your machine undercounter, check
whether you have sufficient space under your
countertop and whether the wiring-plumbing is suitable
to do so.
1. To ensure the stability of the dishwasher for
an underbench installation, if the underbench
dimension is greater than 820mm, any gap between
the dishwasher and the underside of the benchtop
should be bridged with a packing piece. This may
be achieved by wedging a piece of timber between
the dishwasher and the benchtop as shown
2. If required, remove the worktop as shown in the
illustration.
3. To remove the worktop, remove the screws that
hold the worktop which are located at the rear of
the machine; then push the front panel 1cm from
the front
| General | Details |
|---|---|
| Name | Electrolux ESF6768KXA Dishwasher |
| Make | Electrolux |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.69 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Electrolux ESS87300UX Dishwasher
Electrolux EES48401L Dishwasher
Electrolux EFF9392SXA Dishwasher
Electrolux ESZ89400UX 800 SprayZone Dishwasher
Electrolux ESL2500RO Dishwasher
Electrolux KECA7400W Builtin Dishwasher
Electrolux TAPPAN Dishwasher
Electrolux KESC7320L Dishwasher
Electrolux EEC87400W Sliding Door Dishwasher
Electrolux EFC3862MS UltimateCare 300 Compact Dishwasher
BOSCH SMI4EAS23E Dishwasher
BOSCH SMV4EVX02E Dishwasher
KUCHT K6502D Dishwasher
CMA DISHMACHINES EST-66 Conveyor Dishwasher
Miele G5210 Active Plus Dishwasher
ARDESTO DWMB-V609SMH3 Dishwasher
FISHER PAYKEL DD24DDFT9 Series Dishwasher
Indesit I3B L634 B Dishwasher
KitchenAid KDTE104KPS Dishwasher
JENNAIR W11745540A Dishwasher