Home > GERMAN POOL > GERMAN POOL 450 Series Dishwasher
GERMAN POOL 450 Series Dishwasher
Installation Instructions
Installation Instructions
How to Connect the AQUASTOP Safety Supply Hose
Warning!
Electrical Shock Hazard
Disconnect electrical power before installing dishwasher.
Failure to do so can result in death or electrical shock.
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0.04 MPa and 1 MPa. If the pressure is
below the minimum, consult our Service Department for advice.
1. Pull the safety supply hoses completely out from storage compartment
located at rear of dishwasher.
Attention:
The installation of the pipes and electrical equipment should be done by professionals.
2. Tighten the screws of the safety supply hose to the faucet with thread
3/4inch.
3. Turn water fully on before starting the dishwasher.
About Power Connection
Warning
ABOUT THE SAFETY SUPPLY HOSE
For personal safety:
•
•
The safety supply hose consists of the double walls. The hose’s system guarantees its intervention by
blocking the flow of water in case of the supply hose breaking and when the air space between the
supply hose itself and the outer corrugated hose is full of water.
Do not use an extension cord or an adapter plug with this appliance.
Do not, under any circumstances, cut or remove the earthing connection from the power cord.
Warning!
Electrical requirements
- A hose that attaches to a sink spray can burst if it is installed on the same water line as the
dishwasher. If your sink has one, it is recommended the hose be disconnected and the hole plugged.
- Ensure the Aquastop safety supply unit is in a vertical position once installed.
Please look at the rating label to know the rating voltage and connect the dishwasher to the appropriate
power supply. Use the required fuse 10A/13A, time delay fuse or circuit breaker recommended and
provide separate circuit serving only this appliance.
How to disconnect the safety supply hose
1. Turn off the water.
2. Unscrew the safety supply hose from the faucet.
Electrical connection
Ensure the voltage and frequency of the power being corresponds to those on the rating plate. Only
insert the plug into an electrical socket which is earthed properly. If the electrical socket to which the
appliance must be connected is not appropriate for the plug , replace the socket, rather than using an
adaptor or something similar as they could cause overheating and burns.
Connection Of Drain Hoses
Warning! Ensure that proper earthing exists before use.
Insert the drain hose into a drain pipe with a minimum diameter of 4 cm, or let it run into the sink,
making sure to avoid bending or crimping it. The height of drain pipe must be less than 1000mm. The
free end of the hose must not be immersed in water to avoid the back flow of it.
Water Supply And Drain
Please securely fix the drain hose in either position A or position B.
Counter
Ordinary supply hose
Safety supply hose
Back of dishwasher
A
Cold water connection
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is
fastened tightly in place. If the water pipes are new or have not been used for an extended period of
time, let the water run to make sure that the water is clear. This precaution is needed to avoid the risk
of the water inlet to be blocked and damage the appliance.
Drain Hose
B
Warning: Please close the hydrant after using.
Ø 40mm
Water Inlet
Drain Pipe
Attention:
After intsallation, please make sure to keep this manual for future reference. The content
of this manual is very helpful to the user.
Mains cable
P.14
P.15
| General | Details |
|---|---|
| Name | GERMAN POOL 450 Series Dishwasher |
| Make | GERMAN POOL |
| Language | English |
| Filetype | PDF (Download) |
| File size | 6.37 MB |





















































