Home > Ikea > IKEA 68016 Lagan Dishwasher

IKEA 68016 Lagan Dishwasher

ENGLISH  
8
First Use  
Advice regarding the first time use  
Water Hardness Table  
Before installation and first usage of the appliance please read  
carefully „ SAFETY INSTRUCTION” and „ASSEMBLY INSTRUCTION”  
available in the product literature bag. Please remember to  
remove all transport protection parts from the dishwasher.  
Level  
Soft  
°dH German °fH French  
°Clark English  
degrees  
degrees  
degrees  
1
2
3
4
5
0 - 6  
0 - 10  
0 - 7  
Medium  
Average  
Hard  
7 - 11  
11 - 20  
21 - 29  
30 - 60  
61 - 90  
8 - 14  
Filling the salt reservoir  
12 - 16  
17 - 34  
35 - 50  
15 - 20  
21 - 42  
43 - 62  
The use of salt prevents the formation of LIMESCALE on the  
dishes andon the machine’s functional components.  
• It is mandatory that THE SALT RESERVOIR BE NEVER EMPTY.  
• It is important to set the water hardness.  
Very hard  
The salt reservoir is located in the lower part of the dishwasher  
(see PRODUCT DESCRIPTION) and should be filled when the  
Water Softening System  
SALT REFILL indicator light  
in the control panel is lit.  
Water softener automatically reduces water hardness, conse-  
quently preventing scale buildup on heater, contributing also  
to better cleaning efficiency. This system regenerates itself with  
salt, therefore it is required to refill salt container when empty.  
Frequency of regeneration depends on water hardness level  
setting - regeneration takes place once per 6 Eco cycles with  
water hardness level set to 3.  
Regeneration process starts in final rinse and finishes in drying  
phase, before cycle ends.  
Single regeneration consumes: ~3.5 L of water;  
Takes up to 5 additional minutes for the cycle;  
• Consumes below 0.005 kWh of energy.  
1. Remove the lower rack and unscrew  
the reservoir cap (anticlockwise).  
2. Position the funnel (see figure) and  
fill the salt reservoir right up to its  
edge (approximately 1 kg); it is not  
unusual for a little water to leak out.  
3. Only the first time you do this: fill  
the salt reservoir with water.  
4. Remove the funnel and wipe any  
salt residue away from the opening.  
Make sure the cap is screwed on tightly, so that no detergent  
can get into the container during the wash program (this could  
damage the water softener beyond repair).  
As soon as this procedure is complete, run a program without  
loading. The “Pre-Wash” program alone is NOT sufficient.  
Residual saline solution or grains of salt can lead to corrosion,  
irreparably damaging the stainless steel components.  
The guarantee is not applicable if faults are caused by such  
circumstances.  
Only use salt that has been specifically designed for  
dishwashers. If the salt container is not filled, the water  
softener and the heating element may be damaged  
as a result of limescale accumulation. Using of Salt is  
recommended with any type of dishwasher detergent.  
Whenever you need to add salt, it is mandatory to complete  
the procedure before the beginning of the washing cycle to  
avoid corrosion.  
Filling the rinse aid dispenser  
A
Rinse aid makes dish DRYING easier. The rinse aid dispenser  
should be filled when when the dark optical indicator on the  
C
dispenser door becomes transparent.  
C
B
A
1. Open the dispenser B by pressing and pulling up the tab on  
the lid.  
2. Carefully introduce the rinse aid as far as the maximum (110  
ml) reference notch of the filling space - avoid spilling it. If this  
happens, clean the spill immediately with a dry cloth.  
3. Press the lid down until you hear a click to close it.  
NEVER pour the rinse aid directly into the tub.  
Setting the water hardness  
To allow the water softener to work in a perfect way, it is  
essential that the water hardness setting is based on the actual  
water hardness in your house. This information can be obtained  
from your local water supplier. The factory sets the default value  
for the water hardness.  
Switch on the appliance by pressing the ON/OFF button.  
Adjusting the dosage of rinse aid  
If you are not completely satisfied with the drying results, you  
can adjust the quantity of rinse aid used.  
Switch the dishwasher on using the ON/OFF button.  
Switch it off using the ON/OFF button.  
Switch off the appliance by pressing the ON/OFF button.  
• Hold down button  
for 5 seconds, until you hear a beep.  
Switch on the appliance by pressing quickly the ON/OFF  
button.  
The program indicator light of the current set level flashes.  
• Press button  
to select the desired hardness level (see  
• Press button  
three times - a beep will be heard.  
WATER HARDNESS TABLE).  
Switch it on using the ON/OFF button.  
Switch off the appliance by pressing the ON/OFF button.  
Setting is complete!  
The program indicator light of the current set level flashes.  
• Press button  
supplied.  
to select the level of rinse aid quantity to be  
Switch it off using the ON/OFF button.  
Setting is complete!  
GeneralDetails
NameIKEA 68016 Lagan Dishwasher
MakeIkea
LanguageEnglish
FiletypePDF (Download)
File size52.49 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
IKEA 404.755.53 Medelstor Dishwasher
IKEA 404.755.53 Medelstor Dishwasher
IKEA 804.621.67 Lagan Dishwasher
IKEA 804.621.67 Lagan Dishwasher
IKEA RENGÖRA 204.756.05 Dishwasher
IKEA RENGÖRA 204.756.05 Dishwasher
IKEA 9001774317 TORSBODA Dishwasher
IKEA 9001774317 TORSBODA Dishwasher
IKEA 9001774318 Dishwasher
IKEA 9001774318 Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
IKEA VILLBODA Dishwasher
IKEA VILLBODA Dishwasher
IKEA 504.754.25 HYGIENISK Dishwasher
IKEA 504.754.25 HYGIENISK Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Dishwasher
IKEA 905.681.49 OSTVEDA Dishwasher
IKEA 905.681.49 OSTVEDA Dishwasher

IKEA 68016 Lagan Dishwasher