Miele PFD 104 SCVI XXL Dishwasher

1

2

3

4

*INSTALLATION*  

11678880-01  

Installation  

The machine must only be operated  

with the voltage, frequency and fusing  

shown on the data plate.  

Electrical connection  

 All work on the electrical  

connection must be carried out by  

the Miele Professional Service  

Department, a Miele authorised  

technician or a qualified electrician.  

This machine can be converted to a  

different type of power supply in  

accordance with the conversion  

diagram and wiring diagram supplied.  

- The electrical installation must  

comply with current local and  

national safety regulations.  

Converting the machine to a different  

type of power supply can lead to  

longer programme durations,  

resulting in increased energy  

consumption in some programmes.  

The values declared on the label will  

only be achieved if the machine  

remains in the state in which it was  

delivered.  

- The connection to the power supply  

must comply with national  

regulations (plug and socket must be  

accessible for service and  

maintenance work after the machine  

has been installed). An electrical  

safety test must be carried out after  

installation and after any service  

work.  

The data plates are located at the back  

of the dishwasher and along the right  

edge of the open door.  

- If the dishwasher is hard wired to the  

power supply, connection should be  

made via a mains switch with all-pole  

isolation. The mains switch must  

ensure a 3 mm gap between all open  

contacts, and must be able to be  

locked in the off position. The means  

for disconnection must be  

The wiring diagram is supplied with  

the machine.  

The conversion diagram is attached to  

the electrical connection plinth panel  

behind the plinth cover.  

Equipotential bonding connection  

incorporated in the fixed wiring in  

accordance with the wiring rules.  

There is a screw connection point  

marked  at the back of the appliance,  

to which additional equipotential  

bonding can be connected.  

- Equipotential bonding should be  

carried out if required.  

- If replacing the mains connection  

cable, use only original Miele  

replacement parts or a suitable cable  

with core cable ends.  

- For technical data see data plate or  

wiring diagram supplied.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Miele PFD 104 SCVI XXL Dishwasher
Make	Miele
Language	English
Filetype	PDF (Download)
File size	0.05 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• Miele

Miele PFD 104 SCVI XXL Dishwasher Overview

Summary of Contents

• Page 1: Installation The machine must only be operated with the voltage, frequency and fusing shown on the data plate. All work on the electrical connection must be carried out by the Miele Professional Service Department, a Miele authorised technician or a qualified electrician. This machine can be converted to a different type of power supply in accordance with the conversion diagram and wiring diagram supplied. The electrical installation must comply with current local and national safety regulations. The connection to the power supply must comply with national regulations. An electrical safety test must be carried out after installation and after any service work. The data plates are located at the back of the dishwasher and along the right edge of the open door. If the dishwasher is hard wired to the power supply, connection should be made via a mains switch with all-pole isolation. Equipotential bonding connection incorporated in the fixed wiring in accordance with the wiring rules. If replacing the mains connection cable, use only original Miele replacement parts or a suitable cable with core cable ends.
• Page 2: Installation The water pressure must be between 50 and 1000 kPa (0.5 and 10 bar). If the water pressure is lower, the fault message Water intake will appear. If the water pressure is too high, a pressure reducing valve must be fitted. The Miele Waterproof anti-leak system will protect you from water damage throughout its lifetime. Water in the dishwasher must not be used as drinking water. A tap with a 3/4 inch male thread must be provided on site. The machine must be connected to the water supply in accordance with local and national requirements. The water used must comply with national regulations for drinking water quality. If the water supply has a high iron content, there is a danger of corrosion. The DN 10 inlet hose is approx. 1.5 m long terminating in a 3/4 inch female thread.
• Page 3: Installation To avoid any damage to the machine, the dishwasher must only be connected to a fully vented plumbing system. The inlet hose must not be shortened or damaged in any way as it contains electrical components.
• Page 4: Installation Hose positioning with a low water drainage height Connecting the drain hose The machine drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. If the on-site drainage connection is situated lower than the guide path for the lower basket rollers in the open door, the water drain hose must be raised to the height of the guide path for the lower basket rollers with a bend in it. The dishwasher drainage hose should preferably be connected to a separate on-site drain for the dishwasher only. The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm. The drain hose must not be shortened. The drainage length must not be longer than 4 m and the delivery head no higher than 1 m. The drainage system must be able to accommodate a minimum drainage flow of 16 l/min. Make sure that there are no kinks in the hose, and that it is not squashed or stretched.