Home > Whirlpool > Whirlpool WDF540PADW Dishwasher

Whirlpool WDF540PADW Dishwasher

OPTIONS  
CAN BE  
SELECTED  
WITH  
ADDED  
WATER  
GALLONS  
(LITERS)  
ADDED TIME  
TO CYCLE  
WHAT IT DOES  
Activates the TargetClean™ spray jets and provides  
intensified water spray to back of lower level rack.  
Sensor  
Heavy  
Raises main wash  
temperature from  
105°F (41°C)  
0:12 to 0:57  
0 to 4.8  
(0 to 18.2)  
Normal  
May add heat and time to cycle.  
Soak & Clean  
to120°F (49°C).  
Raises main wash temperature to improve cleaning for  
loads containing tough, baked-on food.  
Sensor  
Heavy  
Raises the main  
wash temperature to  
135°F (57°C)  
0:05 to 0:13  
0 to 3.86  
(0 to 14.6)  
Normal  
Soak & Clean  
Sanitizes dishes and glassware in accordance with NSF  
International NSF/ANSI Standard 184 for Residential  
Dishwashers. Certified residential dishwashers are not  
intended for licensed food establishments. The Sani  
indicator indicates at the end of the cycle whether the Sani  
Rinse option was successfully completed. If indicator does  
not activate, it is probably due to cycle being interrupted.  
Sensor  
Heavy  
Raises the main  
wash temperature to  
135°F (57°C) and  
the final rinse  
temperature to  
156°F (69°C)  
0:05 to 1:06  
0:08 to 0:46  
0 to 3.86  
(0 to 14.6)  
Normal  
Dries dishes with heat. This option, with the use of rinse  
aid, will provide the best drying performance. Plastic items  
are less likely to deform when loaded in the top rack. Use  
Heat Dry for optimum dry performance, Turn the Heat Dry  
option off for air dry.  
Sensor  
Heavy  
Normal  
Uses heating  
0
0
element to speed  
drying times. Heat  
Dry option defaults  
to On when any  
cycle is selected  
except for 1- Hour  
Wash.  
Soak & Clean  
Runs dishwasher at a later time. Select a wash cycle and  
options. Each time you press the delay button it will display  
the next available delay time. Press DELAY. Press START/  
RESUME. Close door firmly.  
Available  
with any  
cycle  
Delays start of a  
cycle up to 24 hours.  
0:00  
NOTE: The dishwasher remembers the last Delay you  
selected. To reset the delay time to something other than  
what is displayed, continue to press the Delay button until  
the desired delay time is reached.  
NOTE: Anytime the door is opened (such as, to add a  
dish); START/RESUME must be pressed again to resume  
delay countdown.  
Avoids unintended use of dishwasher between cycles, or cycle and option changes during a cycle.  
To turn on Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Control Lock light will  
stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your dishwasher is  
locked, light flashes 3 times. Dishwasher door can still be opened/closed while the controls are locked.  
To turn off Lock, press and hold SANI RINSE/CONTROL LOCK or DELAY (depending on model) for 3 seconds. Light turns off.  
NOTE: If your model requires you to press and hold DELAY to lock controls, Control Locked LED will be on or off to indicate whether  
Control Lock is active or not.  
Control  
Purpose  
Comments  
Press to start or  
resume a wash  
cycle.  
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED  
flashes. Cycle will not resume until door is closed and START/RESUME is pressed.  
NOTE: If Start/Resume button is located on top of door, push door firmly closed within 3 seconds  
of pressing START/RESUME. If door is not closed within 3 seconds, Start/Resume button LED  
will flash, an audible tone will be heard (on some top control models), and cycle will not start.  
Press to cancel  
wash cycle.  
Close the door firmly. The dishwasher starts a 2-minute drain (if needed). Let dishwasher drain  
completely. Press and hold START/RESUME for 3 seconds.  
To follow progress The Clean indicator glows when a cycle is finished.  
of your  
If you select Sani Rinse option, when cycle is finished, the “Sanitized” indicator glows. If your  
dishwasher cycle.  
NOTE: Indicators  
shown are not  
available on all  
models.  
dishwasher did not properly sanitize your dishes, the light flashes at the end of the cycle. This  
can happen if the cycle is interrupted, or water could not be heated to required temperature. The  
light goes off when you open and close door or press CANCEL.  
5
GeneralDetails
NameWhirlpool WDF540PADW Dishwasher
MakeWhirlpool
LanguageEnglish
FiletypePDF (Download)
File size1.85 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
Whirlpool 2B19 Dishwasher
Whirlpool 2B19 Dishwasher
Whirlpool WFO3O33PLAUS Standard Dishwasher
Whirlpool WFO3O33PLAUS Standard Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool Thron Dishwasher
Whirlpool Thron Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WDF130PAHB Dishwasher
Whirlpool WDF130PAHB Dishwasher

Whirlpool WDF540PADW Dishwasher