AEG FSE63637P Dishwasher
11. TROUBLESHOOTING
Refer to the below table for information on
possible problems.
WARNING!
Improper repair of the appliance may
pose a danger to the safety of the user.
Any repairs must be performed by
qualified personnel.
With some problems, the display shows an
alarm code.
The majority of problems that may occur can
be solved without the need to contact an
Authorised Service Centre.
Problem and alarm code
Possible cause and solution
You cannot activate the appliance.
•
•
Make sure that the mains plug is connected to the mains socket.
Make sure that there is no damaged fuse in the fuse box.
The programme does not start.
•
•
Make sure that the appliance door is closed.
If the delay start is set, cancel the setting or wait for the end of the
countdown.
•
The appliance recharges the resin inside the water softener. The dura‐
tion of the procedure is approximately 5 minutes.
The appliance does not fill with wa‐
ter.
The display shows i10 or i11.
•
•
Make sure that the water tap is open.
Make sure that the pressure of the water supply is not too low. For this
information, contact your local water authority.
•
•
•
Make sure that the water tap is not clogged.
Make sure that the filter in the inlet hose is not clogged.
Make sure that the inlet hose has no kinks or bends.
The appliance does not drain the
water.
The display shows i20.
•
•
•
Make sure that the sink spigot is not clogged.
Make sure that the interior filter system is not clogged.
Make sure that the drain hose has no kinks or bends.
The anti-flood device is on.
The display shows i30.
•
•
•
Close the water tap.
Make sure that the appliance is correctly installed.
Make sure the baskets are loaded as instructed in the user manual.
Malfunction of the water level detec‐
tion sensor.
The display shows i41 - i44.
•
•
Make sure that the filters are clean.
Switch the appliance off and on.
Malfunction of the wash pump or the
•
Switch the appliance off and on.
drain pump.
The display shows i51 - i59 or i5A -
i5F.
The temperature of the water inside
the appliance is too high or malfunc‐
tion of the temperature sensor oc‐
curred.
•
•
Make sure that the temperature of the inlet water does not exceed
60°C.
Switch the appliance off and on.
The display shows i61 or i69.
ENGLISH 21
| General | Details |
|---|---|
| Name | AEG FSE63637P Dishwasher |
| Make | AEG |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.66 MB |
(1 votes, average: 5.00 out of 5)
Loading...
AEG FSK76748P Dishwasher
AEG FSK53617Za Dishwasher
AEG FSK74747P Dishwasher
AEG FSE73507P Dishwasher
AEG GS60AIM Dishwasher
AEG FSB73427Z Dishwasher
AEG FSE74737P Quickselect Dishwasher
AEG FFB73727PM Dishwasher
AEG F8642FI Tall Tub Dishwasher
AEG FFE83800PM Dishwasher
Electrolux GA55GLICN Dishwasher
NEFF S195HCX02G Fully Dishwasher
SHARP QW-NA24S42DI-EE Dishwasher
BOSH SBH4HVX00E Fully Integrated Dishwasher
ATAG VA7214LR 60 cm Dishwasher
Whirlpool DU810SWP Undercounter Dishwasher
AEG FSB34707Z Dishwasher
Kenmore 263.1460 Dishwasher
FRIGIDAIRE GDPH4515AF Gallery Dishwasher
FISHER PAYKEL DD60D4NX9 Dishwasher