Hotpoint H2F HL626 Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
Salt
indicator is lit
SOLUTIONS
Salt reservoir is empty (after refill the salt indica- Refill reservoir with salt (for more information - see page 2).
tor may remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid dispenser is empty (after refill the
rinse aid indicator may remain lit for several
wash cycles).
Rinse aid
indicator is lit
Refill dispenser with rinse aid (for more information - see page 2).
The appliance has not been plugged in
properly.
The dishwasher
won’t start or does
not respond to
commands.
Insert the plug into the socket.
For safety reasons, dishwasher will not restart automatically when power
returns. Press the START/Pause button to resume the cycle.
Power outage.
The dishwasher door is not closed.
ActiveDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 sec. Close the door and press START/Pause.
It does not respond to commands. Display
shows: F9 or F12 and both On/Off
and START/Pause LEDs are blinking rapidly.
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and restart the program. If problem persists,
unplug the appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Display shows: F3
and both On/Off
and START/Pause
LEDs are blinking
rapidly.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher
makes
excessive noise.
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher
by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and run new
program without detergent.
An excessive amount of foam has been pro-
duced.
The crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being
Arrange the crockery correctly (see LOADING THE RACKS).
hindered by the dishes.
The dishes are not
clean.
The wash cycle is too gentle.
An excessive amount of foam has been pro-
duced.
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has
not been shut correctly.
The filter is soiled or clogged.
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt.
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the
water. Display
No water in the water supply or the tap is
closed.
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the
dishwasher and reboot.
shows:
and F6,
The inlet hose is bent.
both On/Off and
START/Pause LEDs
are blinking rapidly.
The sieve in the water inlet hose is clogged; it After having carried out the verification and cleaning, turn off and turn on
is necessary to clean it.
the dishwasher and restart a new program.
Dishwasher finishes
the cycle prematurely.
Display shows: F15
and both On/Off
and START/Pause
LEDs are blinking
rapidly.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance valve
if necessary.
Drain hose positioned too low or siphoning
into home sewage system.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product
information can be found by:
•
•
•
Visiting our website docs.hotpoint.eu and parts-selfservice.whirlpool.com
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s
identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
400011432152E
07/2023 ks - Xerox Fabriano
8
| General | Details |
|---|---|
| Name | Hotpoint H2F HL626 Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 3.66 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7I HP42 L UK Dishwasher
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
beko BDIN38651C Dishwasher
KKT KOLBE DW4505FS Dishwasher
FISHER AND PAYKEL DD60STX6I1 Dish Drawer Dishwasher
FISHER PAYKEL DD24DCHTX9 N Dishwasher
FISHER and PAYKEL DD60DDFHX9 Dishwasher
ARTUSI ADW5001X Dishwasher
SIEMENS SE61IX12TG Dishwasher
FISHER PAYKEL DW60UC6X Built-under Dishwasher
FISHER PAYKEL DD24SCTW9 N Dishwasher
FISHER PAYKEL DD60SDFHX9 Dishwasher