Hotpoint H2F HL626 Dishwasher
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
ZONE WASH 3D
DELAY
The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
Option works with one rack at once. In particular, we
recommend to use it with Mixed and Intensive cycles - thanks to
the additional 3D water jets placed on the bottom o the cavity,
ZONEWASH 3D option allows to save energy or to increase the
washing performance of the dishwasher:
1. Select the program and any desired options. Press the
DELAY button (repeatedly) to delay the start of the program.
Adjustable from 0:30 to 24 hours. With each press of the
button, the delay start increases by: 0:30 if selection below
4 hours, 1:00 if selection is below 12 hours, 4 hours if
selection is above 12 hours. If 24 hours reached, and the
button is pressed, the delayed start is deactivated.
2. Press the START/PAUSE button: the timer will begin
counting down;
• ZONE WASH 3D + MIXED CYCLE: it allows to reduce energy
consumption up to 40%.
• ZONEWASH 3D + INTENSIVE CYCLE: it increases the washing
performances up to 40%. Ideal for very soiled mixed loads,
e.g. pans and saucepans, dishes with heavy encrustation
or difficult-to-clean crockery (grater, vegetable mill, dirty
cutlery).
3. Once this time has elapsed, the indicator light switches off
and the program begins automatically.
How to activate the option:
1. Select a compatible cycle
If at the time of the countdown the START/PAUSE button is
pressed again the DELAY option is cancelled and the selected
program starts automatically.
2. By default the appliance washes dishes in all racks. To wash
only the specific rack, press this button repeatedly:
The DELAY function cannot be set once a program has
been started.
shown on the display (only lower rack)
shown on the display (only upper rack)
DRAIN OUT
To stop and cancel the active cycle, the Drain Out function
can be used.
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only, and to
reduce the amount of detergent accordingly.
A long press of START/PAUSE button, will activate the DRAIN
OUT function. The active program will be stopped and the
water in the dishwasher will be drained out.
If upper rack is removed, please apply detergent directly
to tub instead of detergent dispenser.
ActiveDry
ActiveDry is a convection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying
performance every day. Door opens at the temperature that is safe to
your kitchen furniture, thus door will not be opened when the option
of SHORT TIME is on.
KEYLOCK
A long press (for 3 seconds) of ZONE WASH 3D button,
will activate the KEYLOCK function. The KEYLOCK function
will block the control panel except the ON/OFF button. To
deactivate the KEYLOCK, long press again.
As additional steam protection, special designed protection foil is added
together with the dishwasher (depending on the model type - can be
the need to buy it). To see how to mount protection foil please refer to
(INSTALLATION GUIDE).
WATER TAP CLOSED – Alarm
Flashes when there is no inlet water or water tap is closed.
ActiveDry functionality could be disabled by the user as follows:
• To DISABLE: Switch On, then switch Off. Keep the P button pressed for
5 sec., at the end of 5 sec the dishwasher plays a short beep. Switch
On the machine, the display shows„oOF”.
SHORT TIME
This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying
performance levels.
• To ENABLE: Switch On, then switch Off the machine. Keep the P button
pressed for 5 sec., at the end of 5 sec the dishwasher plays a short beep.
Switch On the machine, the display shows„oOn”.
After selecting the program, press the SHORTTIME button and
the indicator light will switch on. To deselect the option, press
the same button again.
TABLET (Tab)
This setting allows you to optimize the performance of the
program according to the type of detergent used.
A long press (for 3 seconds) of the SHORT TIME button (the
corresponding symbol will light up), will activate the function
if you use combined detergents in tablet form (rinse aid, salt
and detergent in 1 dose).
If you use powder or liquid detergent, this option should be off.
4
| General | Details |
|---|---|
| Name | Hotpoint H2F HL626 Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 3.66 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7I HP42 L UK Dishwasher
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
Whirlpool DU810SWP Undercounter Dishwasher
whirlpool WFE 2B19 X Dishwasher
WDTA50SAKB Dishwasher
IKEA RENGOERA Dishwasher
FISHER AND PAYKEL DD24STX6I Tall Dishwasher
Rasonic RDW-ZW39 Table Top Dishwasher
Hisense HS673A60X Dishwasher
rhima RU-50 Under Bench Dishwasher
BOSCH SMV25BX04R Dishwasher
Kenmore 587.141500 Dishwasher