Hotpoint H7I HP42 L UK Dishwasher
Daily Reference Guide
CLEANING THE SPRAY ARMS
EN
On occasions, food residue
may become encrusted onto
the spray arms and block the
holes used to spray the wa-
ter. It is therefore recommen-
ded that you check the arms
from time to time and clean
them with a small non-me-
tallic brush.
The lower spray arm may be removed
by pulling it upwards and rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it down and
rotating it clockwise.
The top spray arm may be removed
by pressing it up and then rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it upwards and
rotating it clockwise.
To remove the upper spray
you must remove it together
with manifold.
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service whose contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
The salt
Refill the reservoir with salt (for more information - see FILLING THE SALT RESERVOIR).
Check the water hardness setting if necessary - see WATER HARDNESS TABLE.
Salt reservoir is almost empty.
indicator is lit
The salt
indicator is
blinking
Refill the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
Salt reservoir is empty.
The rinse aid
indicator is lit
or blinking
Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for a short time).
Refill the dispenser with a rinse aid (for more information - see FILLING THE RINSE AID DISPENSER).
Descale indicator
is lit or blinking;
«dES» alarm is
displayed.
Descale the appliance immediately using the Self Clean program and a commercially available
descaling product (see OPTIONS AND FUNCTIONS). Refill the reservoir with salt. Check the water
hardness setting. If the appliance is not descaled, it will stop functioning.
Limescale is accumulating on internal components
of the appliance.
The appliance has not been plugged in properly. Insert the plug into the socket.
For safety reasons, the dishwasher will not re-start automatically when power returns.
Open dishwasher door, press START/Pause button and close the door within 4 seconds.
Power outage.
The dishwasher
The dishwasher door is not closed.
ActiveDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
won’t start or does
not respond to
commands.
A cycle is interrupted by door opening for more
than 4 seconds.
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON-OFF/Reset button, switch it back on after approxima-
tely one minute and restart the program. If the problem persists, unplug the appliance for
1 minute, then plug it back in.
The control panel does not respond or F6 E1 is
displayed.
Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE
INSTRUCTION).
The filter is clogged with food residues or limescal.
The dishwasher
won’t drain.
Display shows:
F7 E3 or F9 E1
The drain hose is kinked.
Check the drain hose (see INSTALLATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
Dishes are rattling against each other.
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER). Restart the current cycle by switching OFF the dishwa-
sher, then switch it on again, select a new program, press START/Pause and close the door within
4 seconds. Please do not add any detergent.
The dishwasher
makes excessive
noise.
An excessive amount of foam is present.
Crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The filter is clogged with food residues or limescal. Clean the filter assembly (see CARE AND MAINTENANCE).
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
Spray arms cannot rotate freely, being hindered Arrange the crockery correctly (see LOADING THE RACKS). Check that the upper rack is in correct
by the dishes.
position and adjust (lift up) if necessary.
The wash cycle is too gentle.
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam is present.
The dishes are not
clean.
The cap on the rinse aid compartment has not
been closed correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is clogged with food residues or limescal. Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY).
The salt reservoir is empty. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
5
| General | Details |
|---|---|
| Name | Hotpoint H7I HP42 L UK Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 5.95 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
Hotpoint HFC 3C26 WCUK Dishwasher
BOSCH SMS4EKI06G Dishwasher
Fisher Paykel DW60CSX1 FP AA Dishwasher
eta 239490001B Dishwasher
FISHER PAYKEL DW60U2I1 Dishwasher
BOSCH SMV4HDX52Y-39 Fully Integrated Dishwasher
Miele PFD 103 SCi XXL XXL Dishwasher
KitchenAid KDFE104KWH Two Rack Dishwasher
FISHER AND PAYKEL DD24DT4NX9 Contemporary Tall Dishwasher
Forte F24DWS650PR Dishwasher
ARTUSI ADW5001X Dishwasher