Hotpoint HF9E 1B19 UK Slimline Dishwasher
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when the RINSE AID REFILL
panel is lit.
indicator light in the control
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes
and on the machine’s functional components.
•
•
It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL
A
indicator light
in the control panel is lit .
B
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can
adjust the quantity of rinse aid used.
Make sure the cap is screwed on tightly, so that no detergent can
get into the container during the wash program (this could damage
the water softener beyond repair).
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to avoid
corrosion.
• Press button START/Pause three times.
• Switch it on using the ON/OFF button.
• The START LED light will flash as many times as the level that was set.
SETTING THE WATER HARDNESS
• Set the level of rinse aid quantity to be supplied using the PROGRAM
SELECTION knob (see PROGRAMS TABLE).
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
The factory sets the default value for the water hardness:
• Switch it off using the ON/OFF button
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/Pause for 5 seconds.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine
• Switch on the appliance by pressing the ON/OFF button.
• The ON/OFF LED light will flash as many times as the level that was set.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a mid-
range number (4-5).
• Set the desired water hardness level using the PROGRAM SELECTION
knob (see WATER HARDNESS TABLE).
FILLING THE DETERGENT DISPENSER
Water Hardness Table
To open the detergent dispenser use the opening device C.
Introduce the detergent into the dry dispenser D only. Place
the amount of detergent for pre-washing directly inside the tub.
°dH
German degrees French degrees English degrees
°fH
°Clark
Level
Soft
1
2
3
4
5
0 - 6
0 - 10
11 - 20
21 - 29
30 - 60
61 - 90
0 - 7
1. When measuring out the detergent
refer to the mentioned earlier
information to add the proper
quantity. Inside the dispenser
Medium
Average
Hard
7 - 11
8 - 14
12 - 16
17 - 34
35 - 50
15 - 20
21 - 42
43 - 62
D
the detergent dosing.
2. Remove detergent residues from
the edges of the dispenser and close
the cover until it clicks.
there are indications to help
D
C
Very hard
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
3. Close the lid of the detergent
dispenser by pulling it up until
the closing device is secured
in place.
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL
indicator light switches off.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
button, because it adjusts the program so that the best washing and
drying results are always achieved.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher
detergent.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
2
| General | Details |
|---|---|
| Name | Hotpoint HF9E 1B19 UK Slimline Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.97 MB |

Hotpoint H7I HP42 L UK Dishwasher

Hotpoint H7F HP33 UK Dishwasher

Hotpoint H7F HS41 UK Full Size Dishwasher

Hotpoint H8I HT59 LS UK Dishwasher

Hotpoint H7F HS51 Dishwasher

Hotpoint H7FHS41 Dishwasher

Hotpoint HA3FC10BS7A0S Dishwasher

Hotpoint H7F HS41 X Dishwasher

Hotpoint 869991662940 Dishwasher

Hotpoint H7I HT59 L Dishwasher





















