Home > KitchenAid > KitchenAid KDFE204KPS Dishwasher
KitchenAid KDFE204KPS Dishwasher
■ Do not solder within 6" (15.2 cm) of the water inlet valve.
Sand holes smooth
■ If installed in new construction, make sure the house water
supply lines have been flushed prior to connecting the
dishwasher to remove any debris that may exist in the supply
line.
IMPORTANT: Do not kink or pinch water line, drain hose,
power cord, or direct wire between dishwasher and cabinet.
Remove cardboard from under dishwasher (if used).
NOTE: If replacing an existing dishwasher, it is recommended
to install a new water line and drain hose (supplied) with the
new dishwasher.
Metal
Cabinet
Wood
Cabinet
NOTE: If using a flexible braided hose, replace inlet hose
after 5 years to reduce the risk of hose failure. Record hose
installation or replacement dates on the hose for future
reference.
FILL HOSE TO FILL VALVE CONNECTION
Be sure rubber washer is properly seated in fitting. Slide the 3/4"
(19 mm) fitting of the 90 elbow up to the valve and hand tighten
it to avoid cross-threading. Hand tighten until the coupling is
tight.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover edges of hole with grommet included with
power cord kit.
Using pliers, check the tightness of the coupling. An additional
1/4 to 1/2 turn may be required to seal the rubber gasket. Rout
fill hose out the rear left side of unit.
DRAIN REQUIREMENTS
■ A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, be sure to purchase only Whirlpool
factory-certified parts. To order, refer to the contact information
referenced in your Quick Start Guide.
NOTE: Do not use tape with compression fitting. Do not
over-tighten. Damage to the coupling can result. Route water
supply line out rear of unit before setting unit up.
NOTE: Do not connect multiple drain hoses together.
■ Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter or be connected to an air gap.
ELECTRICAL REQUIREMENTS
WARNING
■ Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (50.8 cm) above subfloor or
floor.
Use of air gap
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
You Must Have:
■ 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply
■ If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
■ Use 1/2" (1.3 cm) minimum I.D. drain line fittings.
WATER SUPPLY REQUIREMENTS
■ This dishwasher has a water heating feature and also requires a
connection to a hot water supply line.
■ A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa)
water pressure can be verified by a licensed plumber.
■ 120°F (49°C) water at dishwasher.
■ 3/8" (0.95 cm) O.D. copper tubing with compression fitting or
flexible braided water supply line.
NOTE: 1/2" (1.3 cm) minimum plastic tubing is not
recommended.
■ A 90° elbow with 3/4" (0.95 cm) hose connection with rubber
washer.
3
| General | Details |
|---|---|
| Name | KitchenAid KDFE204KPS Dishwasher |
| Make | KitchenAid |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.9 MB |

KitchenAid KDTE304RBS Third Level Jet Rack Dishwasher

KitchenAid KDTF324PPA Dishwasher

Kitchenaid MVWC565FW1 Dishwasher

KitchenAid w11323304 Dishwasher

KitchenAid KDFE104KWH Two Rack Dishwasher

KitchenAid KDTE104KPS Dishwasher

KitchenAid KDFE104KBL Front Dishwasher

KitchenAid KDTF924PPS Flush Cabinet Dishwasher

KitchenAid KDTE304RBS Level Jet Rack Dishwasher

KitchenAid KDF Series Dishwasher





























