maxima 09240000 Dishwasher

1

2

3

4

5

6

7

8

9

10

11

12

13

14

USER MANUAL  

DISHWASHER  

MODEL: 09240000  

09240010  

09240020  

09240030  

09240040  

09240050  

09240060  

09240070  

READ THIS MANUAL CAREFULLY BEFORE USING  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	maxima 09240000 Dishwasher
Make	maxima
Language	English
Filetype	PDF (Download)
File size	0.91 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL DISHWASHER INSTRUCTIONS & USER MANUALS
• maxima

maxima 09240000 Dishwasher Overview

Summary of Contents

• Page 1: User manual for dishwasher models 09240000 to 09240070. Read this manual carefully before using.
• Page 2: Instruction manual for dishwashers Risks and important warnings Normal operating conditions Preface Installation Unpacking Positioning Electrical connection Water circuit hookup Connection to the drain line Using the machine
• Page 3: Instruction manual for dishwashers Read the instruction manual carefully before starting the machine. The warnings contained in the manual provide important information on safety and installation, use and maintenance. Risks and important warnings This appliance is intended solely for the use for which it was designed. Any other use is improper and therefore hazardous. The specialised technician responsible for installing the appliance must instruct the user on its operation and any attendant safety measures, including practical demonstrations. Only the manufacturer or an authorised service centre with qualified staff may work on the machine, even in case of malfunction, using only original spare parts. Always disconnect or isolate the machine from its power and water supplies before servicing, repairing or cleaning it. The machine may not be used by persons untrained in its use. Children must not play with the appliance. Cleaning and maintenance by the user must not be performed by unsupervised children. The machine must not be kept powered up when not in use. If the power cable is damaged, it must be replaced by the manufacturer or an authorised technical assistance service.
• Page 4: Instruction manual for dishwashers Never place your bare hands in the wash solution. If you notice any malfunction or fluid leak, immediately disconnect the power supply and shut off the water supply. Do not install the dishwasher in the vicinity of heat sources over 50°C. Never leave the dishwasher exposed to the weather. The dishwasher may not be installed outdoors without proper cover. Never start a wash programme without the overflow in the tub. The installer is responsible for checking that the grounding system is fully operational. At the end of testing, the installer must issue a written declaration stating that the machine has been installed and tested in accordance with established legislation and good practice. Do not clean the appliance with steam or water jets. Max inlet water temperature: 50°C.
• Page 5: Instruction manual for dishwashers Warnings: Keep all documentation in the vicinity of the appliance; make it available to the technicians and operators charged with operating it and keep it in good condition in a safe place, along with extra copies for frequent reference. The operator must read, understand and familiarise himself with the contents of this manual before working on or with the appliance. The appliance is intended solely for professional heavy duty dishwashing applications and must be installed, operated and serviced only by qualified persons according to the manufacturer's instructions. Warranty: The manufacturer is not liable for any damage or injury resulting from failure to observe the instructions or improper use of the machine. Installation and repair by unauthorised technicians and the use of non-original spare parts immediately void the warranty. Proper installation is essential to the good operation of the appliance. The appliance may only be installed by qualified persons authorised to do so. Check the condition of the packaging, and note any evident damage on the shipping bill. Before positioning the appliance, set up the electrical power supply, water supply and drain connections. The appliance is intended for fixed installation only; any other approaches must be agreed with and approved by the manufacturer.
• Page 6: Instruction manual for dishwashers Electrical connection The power supply must be fitted with an omnipolar circuit breaker to break all contacts including neutral, with a contact gap of at least 3 mm. The master power switch must be fitted to the power line in the vicinity of the installation and may be connected to only one machine at a time. The mains voltage and frequency must match the nameplate ratings. The installation must include a grounding system conforming with established electrical safety legislation. This appliance conforms to EN/IEC 61000-3-11 certification if the system impedance is less than or equal to the maximum specified. The power cable must be exclusively type H07RN-F with current capacity at 60°C. The appliance must also be connected to an equipotential system. The equipotential cable must have a cross section of 10 mm². Respect the polarities indicated in the wiring diagram. Do not use multi-sockets, adapters, or cables of inadequate cross section or type.
• Page 7: Instruction manual for dishwashers Water circuit hookup The appliance must be connected to its water supply with a flexible hose. A shut off valve must be installed between the water supply line and the appliance's solenoid valve. The water supply, temperature and pressure must be compatible with the ratings shown on the technical data plate on the machine. Make sure that the water supply flow rate is no less than 20 l/min. If the water hardness is greater than 14 °f (8 °dH), we recommend using an internal water softener. If the water has a very high residual concentration of high conductivity minerals, we recommend installing a demineralisation system. Machines intended for use with desalinated water or with high sodium chloride concentration must be ordered specifically. Connection to the drain line The drain line must consist of a free drain sump with siphon suited to the flow capacity of the drain hose supplied with the appliance. The tub drains under gravity, so the drain sump must be lower than the machine's base. If the drain is not lower than the base of the appliance, you can use the version with drain pump. Always check that the drain works properly and is not blocked. Rinse aid and detergent The rinse aid and detergent are dispensed by the machine's integral dispenser. The dose is set by the installer in relation to the hardness of the water, and he also calibrates the dispensers themselves. Never use chlorine or hypochlorite based detergents.
• Page 8: Instruction manual for dishwashers Using the machine Key and symbols The arrangement of buttons and LEDs may vary according to the machine type. Switching the dishwasher on Turn on the main power switch and open the external water tap. Press ON/OFF. The POWER LED comes on and filling begins automatically. Filling the rack Use a suitable rack, fill without overloading and without overlapping the dishes. Always wipe the dishes before placing in the dishwasher. Cycle selection and start-up Select the washing cycle suited to the type of dishes using PROGRAMME SELECTION. Start the programme by pressing the START button; the CYCLE UNDERWAY LED starts to flash. When the cycle is completed, the CYCLE UNDERWAY LED goes off.
• Page 9: Instruction manual for dishwashers Select the washing cycle suited to the type of dishes using programme selection; with the button pressed, the shorter cycle is enabled. Press start for automatic start. Lower the hood, the cycle starts automatically and the cycle underway led starts to flash. When the cycle is completed the cycle underway led goes off. For rapid drying, remove the rack from the machine as soon as the cycle finishes. To stop a wash cycle early, press start. Switch the dishwasher off. If present, remove the integral filter. Wait for the tub to empty completely. At the end of the day always drain the machine as described in the section machine draining.
• Page 10: INSTRUCTION MANUAL FOR DISHWASHERS MAINTENANCE Before doing any maintenance, completely drain out all water, shut off the power supply and close the water supply cock. Do not use water under pressure - it can damage the electrical equipment. Only wash the body panelling when it is cold, using only product specifically designed for steel. If there is a risk of ice forming, drain the water from the boiler and wash pump. To keep the machine in good working order, it must be maintained regularly as explained below. We recommend periodically running a sanitising treatment with suitable non-corrosive commercial products. Run the cleaning procedure at the end of the day or when you see the filters are dirty. Remove and clean the baskets. Do not use abrasive products to clean the tub. The wash and rinse arms are easily removed in order to clean their nozzles and prevent blockage/encrustations.
• Page 11: Instruction manual for dishwashers Self diagnostics The machine is equipped with a self-diagnosis system that registers and warns of a number of malfunctions via the fast-flashing LEDs. Electro-mechanical safety device. The boiler or tub safety thermostats have cut in, or the tub level safety pressure switch has been triggered. Check that the drain is not blocked. Switch the dishwasher off and then on. Water filling in tank fault. The tank has not filled correctly. Check the water supply and/or the presence of the overflow. Switch the dishwasher off and then on and fill again. Rinsing temperature reset fault. The boiler temperature did not reset in the set time during the washing cycle. Switch the machine off and then on and run a new cycle. Tub or boiler thermometer fault. The machine does not read the tub or boiler temperature value. Switch the dishwasher off and then on. WARNING! Switching the dishwasher off and then on again resets the signals. If after carrying out the instructions given the problem persists, contact an Authorised Service Centre.
• Page 12: Instruction manual for dishwashers Dosing unit settings If the machine is equipped with dosing units, the settings can be changed as follows: Machine in standby with door open. Simultaneously hold pressed the DRAIN and START buttons. The CYCLE LED will start flashing, indicating the machine is in programming mode. Press the START button to adjust the DETERGENT dosing time; each press is equivalent to one second. Press the DRAIN button to adjust the RINSE AID dosing time; each press is equivalent to one second. Close the door and turn on the machine by pressing the ON-OFF button to save the settings. Each time the machine enters programming mode, these settings will be erased. Scrapping Our machines do not contain materials requiring special handling. The mark applied to the product indicates it must not be scrapped with domestic waste when it reaches the end of its service life. To prevent damage to the environment or health risks due to improper scrapping, keep this product separate from other waste and recycle it. Domestic users are requested to contact their local authority for information on sorted waste disposal and recycling for this type of product. Corporate users are requested to contact their local authority and check the terms and conditions of the purchase contract. Environment Respect for the environment Proper use of the dishwasher can improve its environmental footprint if the following simple rules are observed: Only wash full baskets. Switch the dishwasher off when not using it. Keep the machine closed when it is in standby. Use wash programmes suited to the amount of soiling. Supply the machine with hot water, if gas heated. Make sure the drains flow into a suitable sewer. Do not exceed the recommended dose of detergent.
• Page 13: Instruction manual for dishwashers. Appendix. UK.
• Page 14: Page 14