Home > Westinghouse > Westinghouse WSF6606 Dishwasher
Westinghouse WSF6606 Dishwasher
MAINTENANCE AND CLEANING
FAILURE CODES AND WHAT TO DO IN CASE OF FAILURE
Spray arms
F1
Leak detection
Draining fault
•
•
Switch off the dishwasher and close the tap.
Contact the service centre.
Check whether the holes for the upper and lower spray
arms are clogged. If there is any clogging, remove the
spray arms and clean them under water.
F2
•
•
•
•
•
•
Cancel program and power off machine, then check the following.
Spigot on sink trap is clogged.
Check if the drain spigot membrane has been removed.
Drain hose is clogged.
You can remove the lower spray arm by pulling it
upwards, while the upper spray arm can be removed by
turning the lock nut to the left. Be sure that the nut is
perfectly tightened when refitting the upper spray arm.
Filters of the dishwasher may be clogged.
If error continues contact the service centre.
F3
F5
Water overfill
•
•
Close the tap.
Contact the service centre.
Water supply fault
•
•
Make sur e the water tap is open and the main water supply is on.
Close he tap, disconnect the hose and clean the filter at the tap
connection end.
•
•
Check the inlet hose is not kinked.
If error continues contact the service centre.
F6
Faulty heater sensor
•
•
•
•
•
•
Contact the service centre.
Contact the service centre.
Contact the service centre.
Contact the service centre.
Restart the dishwasher.
F7
Overheating (water temperature too high)
Not heating
F8
F9
Flow control position error
Power supply fault
FE
H01 – H24
Delay has been selected
Cancel the delay setting.
PRACTICAL AND USEFUL INFORMATION
1
Whenever you will not be operating your machine:
consumption, washing and drying performance.
•
•
•
Unplug the machine and then turn the water
4
Scrape off food soils before you place dirty dishes
in the machine.
off.
5
6
7
Operate the machine after it is completely full.
Use pre-washing program only when necessary.
Leave the door slightly ajar in order to prevent
the formation of unpleasant odours.
Hose filter
The inlet hose filter reduces contamination (sand, clay,
rust etc.) that might be occasionally carried in through
the main’s water supply or the indoor plumbing, and
avoids damage to dishwasher components. Check the
filter and the hose from time to time and clean them if
necessary. To clean the filter, first turn off your tap and
then remove the hose. After removing the filter from the
hose, clean it under the tap. Insert the cleaned filter back
into its place inside the hose. Refit the hose and check
that there are no leaks.
Keep the machine interior clean.
Observe program information and average
consumption values table when selecting a
program.
2
Eliminating water droplets:
•
•
•
Wash the dishes with the intensive program.
Increase the rinse aid setting.
8
9
Since the machine will reach high temperatures,
it should not be installed near a refrigerator.
If plastic items are washed, water drops on these
items will be unavoidable. Programs with higher
temperatures and increased rinse aid settings
may reduce the water drops. Check that the
plastic items are suitable for dishwasher use.
If the appliance is located where the risk of freezing
exists, you must completely drain the water that
has remained in the machine. Turn off the water tap,
disconnect the water inlet hose from the tap and
allow the interior water to drain.
3
Correctly loaded dishes will give the best energy
MAINTENANCE
22
MAINTENANCE
23
MAINTENANCE AND CLEANING
MAINTENANCE AND CLEANING
| General | Details |
|---|---|
| Name | Westinghouse WSF6606 Dishwasher |
| Make | Westinghouse |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.2 MB |

Westinghouse WSF6602XB 14 Place Dishwasher

Westinghouse WSF6604WA Dishwasher

Westinghouse WSF6604XB Dishwasher

Westinghouse WSF6606XB Dishwasher

Westinghouse WSF6608XB Dishwasher

Westinghouse WSF6608KXB Sensor Wash Dishwasher

Westinghouse WSF6602WB Dishwasher

Westinghouse WSF6606KXB Dishwasher

Westinghouse WSF6604WB Dishwasher

Westinghouse WSU6608XB Dishwasher




























