Home > Westinghouse > Westinghouse WSF6606 Dishwasher
Westinghouse WSF6606 Dishwasher
INSTALLING THE MACHINE
INSTALLING THE MACHINE
the hose.
Positioning the machine
Water drain hose
WARNING
•
The first time you use the appliance, make sure that
there is no leakage.
•
When considering the location for the dishwasher,
ensure that there is adequate space to enable
loading and unloading of the dishes
The water drain hose can be
Electrical Connection
connected either directly to
the water drain hole or to the
sink outlet spigot. Using a
hose hook (if available), the
water can be drained directly
into the sink by positioning
the hose hook over the edge
of the sink.
•
The water inlet hose has a safety valve and a sheath
with an inner mains cable.
The plug of your machine should be connected to an earthed
outlet that supplies suitable voltage and current. If there is no
earthing installation, have a competent electrician carry out
an earthing installation. In case of usage without earthing
installed, our company will not be responsible for any loss of
usage that might occur.
•
•
Do not put your machine in any location where
the ambient temperature can fall below 5°C.
After the connections are made, the tap should be
turned on fully and checked for water tightness. For the
safety of your machine, make sure to always turn off the
water inlet tap after each wash program
is finished.
Before positioning, take the machine out of its
packaging by following the warnings located on
the package.
The indoor fuse current value should be 10-16 A.
•
Position the machine close to a water tap and drain.
You need to postion your machine, taking into
consideration that its connections will not be altered
once they are made.
Floor level
Your machine is designed for 220-240 V. The machine
should not be plugged in during installation.
WARNING
•
•
Always use the molded plug supplied with your machine.
This connection should be at a minimum of 50 cm and at
a maximum of 110 cm above the base of the dishwasher.
•
•
Do not grip the machine by its door or panel in
order to move it.
NOTE: Aquastop inlet hose has
Running in low voltage will cause a decline in
washing quality.
components using 240V. Do not cut
Aquastop inlet hose. Do not let it get
folded, twisted, kinked or crushed.
Take care to leave a certain clearance from all sides of
the machine so that you can comfortably move
it back and forth during cleaning.
•
The machine’s electrical cable should be replaced by
an authorised service or an authorised electrician only.
Failure to do so may lead to accidents.
WARNING
•
Make sure that the water inlet and outlet hoses do
not get squeezed while positioning the machine.
Also, make sure that the machine does not stand
on the electrical cable. Adjust the machine’s feet so
that it is level and stable. Proper positioning of the
machine ensures problem-free opening and closing
of its door.
WARNING
Maximum drain hose length
is 4m. Longer hose length will prevent correct draining,
and result in poor wash performance.
•
•
•
For safety purposes, always make sure to disconnect the
plug when a wash program is finished.
NOTE: A water tempering valve is required if the water
temperature is
over 60°C.
In order not to cause an electric shock, do not unplug
when your hands are wet.
When disconnecting your machine from the mains supply,
always pull from the plug. Never pull the cord itself.
•
If the door of your machine does not close properly,
check if the machine is stable on the floor; if not,
adjust the feet and ensure it is level and stable.
CAUTION
Fitting the machine undercounter
Always use new hoses when you connect the appliance
to the water mains. Old hoses must not be used. The
water inlet hose must be examined at an interval of twelve
months for deterioration and replaced if necessary.
If you wish to fit your machine undercounter, check whether
you have sufficient space under your countertop and whether
the wiring-plumbing is suitable to do so.
Water connection
Ensure that the indoor plumbing is suitable for installing
a dishwasher and complies with AS/NZS 3500.1.
Also, we recommend that you fit a filter at the entrance
of your place or apartment so as to avoid any damage to
your machine because of any contamination (sand, clay,
rust etc) that might be occasionally carried in through
the main’s water supply or the indoor plumbing, and to
avoid problems of staining and formation of deposits
after washing.
In order to pass the safety valve through the kitchen
cabinets, an opening of at least 45mm x 90mm is
needed.
1
To ensure the stability of the dishwasher for an
underbench installation, if the underbench dimension is
greater than 820mm, any gap between the dishwasher
and the underside of the benchtop should be bridged
with a packing piece. This may be achieved by wedging
a piece of timber between the dishwasher and the
benchtop as shown
2
3
If required, remove the worktop as shown in the
illustration.
30cm
min.
Water inlet hose
To remove the worktop, remove the screws that hold the
worktop which are located at the rear of the machine;
then push the front panel 1 cm from the front towards
the rear and lift it.
Do not use the water inlet hose of
your old machine, you must use the
new water inlet hose supplied with
your machine. Before connecting
the water inlet hose to the water
tap, ensure clean water is flowing
from the tap before making the
Timber
Filler piece
wedging
piece
cut to suit
installation
1
2
Bench top
598
598
3mm gap
connection. Connect the water inlet
hose directly to the water inlet tap.
The pressure supplied by the tap
should be at a minimum of 0.03
3
Water drain hose
If you connect the water
drain hose to a trap spigot
under the sink, remove the
MPa and at a maximum of 1 MPa. If
the water pressure is above 1 MPa, a pressure-relief valve
should be installed.
Remove
entire
plastic membrane. If you
internal
do not remove the entire
membrane, remaining food
can cause a blockage in the
drain hose spigot. Ensure a
hose clamp is used to secure
the hose to the spigot.
membrane
WARNING
Only turn the locking nut to secure hose - do not turn
INSTALLATION
8
INSTALLATION
9
INSTALLING THE MACHINE
INSTALLING THE MACHINE
| General | Details |
|---|---|
| Name | Westinghouse WSF6606 Dishwasher |
| Make | Westinghouse |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.2 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Westinghouse WSF6602XB 14 Place Dishwasher
Westinghouse WSF6604WA Dishwasher
Westinghouse WSF6604XB Dishwasher
Westinghouse WSF6606XB Dishwasher
Westinghouse WSF6604WB Dishwasher
Westinghouse WSU6608XB Dishwasher
Westinghouse WSF6608XB Dishwasher
Westinghouse WSF6608KXB Sensor Wash Dishwasher
Westinghouse WSF6602WB Dishwasher
Westinghouse WSF6606KXB Dishwasher
FISHER AND PAYKEL DD60DHI9 Integrated Dishwasher
GRUNDIG GR5500 Dishwasher
Whirlpool 3C26 Dishwasher
Samsung DW60 7 Series Dishwasher
Haier HDWE15-46BK6EG Dishwasher
Bauknecht BFP 5O41 PLT X Dishwasher
GAGGENAU 11029813 Fully- Dishwasher
BOSCH SMI4HAS19E Integrated Dishwasher
Hotpoint H0I D534A S Fully Dishwasher
Jackson DishStar LT Temperature Undercounter Dishwasher