Whirlpool WFE 2B19 X UK Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt indicator
is lit
Salt reservoir is empty. (After refill the salt indica- Refill reservoir with salt (for more information - see page 2).
tor may remain lit for several wash cycles).
Adjust water hardness - see table, page 2.
Rinse aid
indicator is lit
Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for several wash cycles).
Refill dispenser with rinse aid (for more information - see page 2).
The dishwasher
won’t start or does
not respond to
commands.
The appliance has not been plugged in properly. Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press START/Pause button and close the door within 4 seconds.
Power outage.
The dishwasher door is not closed.
NaturalDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for more
than 4 seconds.
Press START/Pause and close the door within 4 seconds.
It does not respond to commands.
Switch off the appliance by pressing the ON/OFF button, switch it back on after approxi-
Display shows: 9 or 12 and On/Off LED is blink- mately one minute and restart the program. If problem persists, unplug the appliance for
ing rapidly
1 minute, then plug it back in.
The dishwasher
won’t drain.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Display shows:
3 and On/Off LED is
blinking rapidly
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes excessive
noise.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program, press
START/Pause and close the door within 4 seconds. Please do not add any detergent.
An excessive amount of foam has been produced.
The dishes are not
clean.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hin-
dered by the dishes.
The wash cycle is too gentle.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not
been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the
water.
Display shows: H,
6 and On/Off LED is
blinking rapidly
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
The sieve in the water inlet hose is clogged; it is After having carried out the verification and cleaning, turn off and turn on the dish-
necessary to clean it washer and restart a new program.
The inlet hose is bent.
Dishwasher finishes Drain hose positioned too low or siphoning into Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
the cycle prema-
turely.
home sewage system.
siphoning into home sewage system, install air admittance valve if necessary.
Display shows: 15
and On/Off LED is
blinking rapidly
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product
information can be found by:
•
•
•
Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
Using QR Code
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s
identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
400011666864
02/2023 ks - Xerox Fabriano
8
| General | Details |
|---|---|
| Name | Whirlpool WFE 2B19 X UK Dishwasher |
| Make | Whirlpool |
| Language | English |
| Filetype | PDF (Download) |
| File size | 36.92 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Whirlpool 2B19 Dishwasher
Whirlpool WFO3O33PLAUS Standard Dishwasher
Whirlpool W11323304G Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
Whirlpool FINPUTSAD Dishwasher
Whirlpool W7U HS31 X Dishwasher
Whirlpool Thron Dishwasher
Whirlpool WDF332PAMS 24 Front Tall Tub Dishwasher
Whirlpool WRF540CWHZ Dishwasher
Whirlpool WDF130PAHB Dishwasher
BOSCH SPS4EMW61E Dishwasher
BOSCH SMD6HCX4FR Dishwasher
Hotpoint HFC 3C26 WCUK Dishwasher
SIEMENS SR63EX24ME Dishwasher
FISHER PAYKEL DD24SVT9 Dishwasher
BOSCH SMS44DW01T Dishwasher
Whirlpool WDF340PAMW 24-Inch Dishwasher
BOSCH SMV6HVX00I Fully- Dishwasher
FISHER AND PAYKEL DW60FC4B2 Dishwasher
FISHER PAYKEL DD60D4ZB9 Double Dishwasher