AEG F8642FI Fully Integrated Tall Tub Dishwasher
program will not be active. Besides, the
machine gives audible warning via buzzer.
Programming The Washing Time Delay
Timer
If an economical electricity tariff is applied
in your region, you can use the Delay
Timer function to wash your dishes during
appropriate hours. You can delay the
start of the selected program until 19
hours. Delay Timer cannot be set after the
program starts.
1. Press the Delay Timer function key after
selecting the washing program and other
auxiliary functions.
2. Once you press the Delay Timer key,
Display will show “1h” and Display will
show program number, program duration
and delay time alternately for 2 seconds.
3. Set the desired time by pressing the
Delay Timer key. Time will increase with the
increments of 1 hour every time you press
the key.
Sanitize Key
Sanitize function raises the water
temperature in the final rinse.
i.Sanitized Indicator
If the program selected with the Sanitize
option is successfully sanitized, Sanitized
Indicator lights up at the end of the
program. If the washing cycle is interrupted
or adequate water heating cannot be
achieved, the Sanitized Indicator may not
light.
ii. “Available programs and options are
indicated on program Table and Options
Table charts.
Extra Fast Key
Select the Extra Fast option to decrease
the duration of a washing program,
providing more economical water usage.
4. In order to start the selected program
with delay, Start/Pause key should be
pressed and the door of the dishwasher
must be closed within 4 seconds.
Extra Dry Key
The machine changes the water
temperature from the value described for
each different program and the extra dry is
performed.
NOTE: The use of Delay Timer has a
special case.
a. Assume that you have selected a
program with delay and pressed Start/
Pause key. After a length of time, you have
opened the door of the machine. If the door
of the machine is closed within 4 seconds,
the machine resumes on for the duration of
delay timer. This is also valid if the door of
the machine is not closed within 4 seconds.
Hi-Temp Key
When this option is selected, both the water
temperature and the washing time are
increased.
Half Load Key
It is used to operate the machine without
loading it completely.
1. Load your dishes in the machine as you
like.
Changing the settings while Delay Timer
is enabled
While the Delay Timer function is activated,
you cannot make changes in the washing
program, auxiliary functions or the duration
of delay time.
i. Program and auxiliary functions cannot
be set/changed after the program has
started.
2. Turn the machine on with On/Off key.
3. Select the desired program and press
the Half Load key. The Half Load indicator
will light on the display.
4. Press Start/Pause key to start the
selected program and close the door of the
machine.
To cancel the Delay Timer function
5. With the Half Load function you can save
power while using the lower and/or upper
baskets of the machine.
1. Open the door of the dishwasher
2. Press and hold program
Delay Timer key for 3 seconds
3. At the end of 3 seconds delaying process
will be cancelled.
i. You can select and start a new program
following the cancellation of Delay Timer
function.
USA-CAN - 26
ii. Delay Timer function can not be set after
Rinse Aid Indicator
the program starts.
Please check the rinse aid indicator on the
control panel to see whether there
is adequate amount of rinse aid in the
dishwasher. You need to refill the rinse aid
reservoir with rinse aid whenever rinse aid
warning indicator appears on the control
panel of your machine.
Starting The Program
Open the door of your machine. Select
the program and auxiliary functions. The
program duration and program number will
appear on the display alternately. Press
“Start/Pause + On/Off” key. Close the door
within 4 seconds, the program will start.
If 4 seconds is exceeded and the door is
closed, program will not start.
End of Program
“00” will be displayed when the washing
programme is over. Buzzer sounds 5 times
each at 5 minutes intervals (in 0, 5, 10 and
15 minutes) in total 4 different times.
Your machine performs water softening
based on model hardness level of
the supply water (Model depending).
Remaining time displayed towards the end
in some programs can be different from the
time indicated at the beginning due to this
process. The total time can also change
while the program is running depending
on the ambient temperature where your
machine is installed, temperature of the
supply water and amount of the dishes.
If the door is opened while the machine
is running, the machine will switch to the
standby mode. Press Start/Pause key and
close the machine door within 4 seconds,
then the program will resume.
1. Open the door of the machine.
2. Press Start/Pause + On/Off key to turn
off your machine.
i. Leave your dishes in the machine for
about 15 minutes to cool down after
they are washed. Your dishes will dry
in a shorter time if you leave the door
of your machine ajar during this period.
This process will increase the drying
effectiveness of your machine.
Water Cut - Off Warning
If mains water is cut or water inlet tap is
turned off the machine can not take water
in and “FF” will flash continuously on the
display. As long as the problem continues,
the washing program is stopped and water
inlet is checked regularly by the user. If the
water inlet is cleared, the machine gets
ready to start a new program.
Child (Key) Lock
Not available.
Cancelling The Program
1. Press program Selection + Cancel key
for 3 seconds to cancel the program.
2. After 3 seconds, “1” will appear on
the display. For a couple of minutes the
machine will fulfill the necessary operations
required to cancel the program.
i. There might be residues of detergent or
rinse aid left in the machine and/or on the
pieces being washed depending on the
step the program you have cancelled was
in.
Overflowing Warning
If the machine intakes too much water or
there is leakage at any of the compo-nents
then the machine will detect this and “F1”
will flash on the display. As long as the
overflowing continues, safety algorithm
will be active and try to discharge the
water. If overflowing stops and safety is
assured, “F1” will disappear. If “F1” does
not disappear, there is a permanent fault. In
this case, theauthorized service should be
contacted.
Salt Indicator (Model Depending)
Please check the salt indicator on the
control panel to see whether there is
adequate amount of softening salt in the
dishwasher. You need to refill the salt
reservoir with salt whenever salt warning
indicator appears on the control panel of
your machine.
USA-CAN - 27
Infoled 2.1 (Model Dependent)
Infoled that is positioned on the bottom
side of the dishwasher shines a light on to
floor to indicate the current status of the
dishwasher during washing.
LED Indicator
State of the Machine
The machine is running a
program.
Red, continuous
Red, flashing
A program is cancelled.
The machine has a fault. Refer
to section "Automatic fault
warnings and what to do".
Red, flashing
rapidly
Green, continuous
A program is finished.
USA-CAN - 28
| General | Details |
|---|---|
| Name | AEG F8642FI Fully Integrated Tall Tub Dishwasher |
| Make | AEG |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.2 MB |
(1 votes, average: 5.00 out of 5)
Loading...
AEG FSK76748P Dishwasher
AEG FSK53617Za Dishwasher
AEG FSK74747P Dishwasher
AEG FSE73507P Dishwasher
AEG GS60AIM Dishwasher
AEG FSB73427Z Dishwasher
AEG FSE74737P Quickselect Dishwasher
AEG FFB73727PM Dishwasher
AEG F8642FI Tall Tub Dishwasher
AEG FFE83800PM Dishwasher
FISHER PAYKEL DW24UNT2X2 Dishwasher
HJC V31 Carbon Dishwasher
PHILCO PD 1045 EA Dishwasher
HAVA R01 Compact Dishwasher
BOSCH SMV4HTX03E Dishwasher
BOSCH SMP4ECS79S Dishwasher
BOSCH SMS6ZCI00G Dishwasher
BOSCH SMS46NI10M Dishwasher
KitchenAid W11775083 Dishwasher
FISHER PAYKEL DD60SDFHX9 Single DishDrawer Dishwasher