AEG FSE84727P Dishwasher
ENGLISH
25
Problem and alarm code
Possible cause and solution
The level of water inside the
appliance is too high.
The display shows iF1.
•
•
•
Switch the appliance off and on.
Make sure that the filters are clean.
Make sure that the outlet hose is installed at the right
height above the floor. Refer to the installation instruc‐
tions.
The appliance stops and
starts more times during op‐
eration.
•
•
It is normal. It provides optimal cleaning results and en‐
ergy savings.
The programme lasts too
long.
If the delay start option is set, cancel the delay setting or
wait for the end of the countdown.
Activating options increases the programme duration.
•
•
The displayed programme
duration is different than the
duration in the consumption
values table.
Refer to the consumption values table in the chapter
"Programme selection".
The remaining time in the
display increases and skips
nearly to the end of the pro‐
gramme duration.
•
This is not a defect. The appliance is working correctly.
Small leak from the appli‐
ance door.
•
•
The appliance is not levelled. Loosen or tighten the ad‐
justable feet (if applicable).
The appliance door is not centred on the tub. Adjust the
rear foot (if applicable).
The appliance door is diffi‐
cult to close.
•
The appliance is not levelled. Loosen or tighten the ad‐
justable feet (if applicable).
•
•
Parts of the tableware are protruding from the baskets.
The appliance door opens
during the wash cycle.
The AirDry function is activated. You can deactivate the
function. Refer to "Basic settings".
Rattling or knocking sounds
from the inside of the appli‐
ance.
•
The tableware is not properly arranged in the baskets.
Refer to basket loading leaflet.
•
•
Make sure that the spray arms can rotate freely.
The appliance trips the cir‐
cuit-beaker.
The amperage is insufficient to supply simultaneously all
the appliances in use. Check the socket amperage and
the capacity of the meter or turn off one of the applian‐
ces in use.
•
•
Internal electrical fault of the appliance. Contact an Au‐
thorised Service Centre.
The appliance is switched
on but does not operate.
The display shows PF.
Power supply is out of the operating range. The wash
cycle is temporarily interrupted and resumes automati‐
cally once the power is restored.
The appliance switches off
during operation.
•
Complete power outage. The wash cycle is temporarily
interrupted and resumes automatically once the power
is restored.
| General | Details |
|---|---|
| Name | AEG FSE84727P Dishwasher |
| Make | AEG |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.8 MB |
(1 votes, average: 5.00 out of 5)
Loading...
AEG FSK76748P Dishwasher
AEG FSK53617Za Dishwasher
AEG FSK74747P Dishwasher
AEG FSE73507P Dishwasher
AEG GS60AIM Dishwasher
AEG FSB73427Z Dishwasher
AEG FSE74737P Quickselect Dishwasher
AEG FFB73727PM Dishwasher
AEG F8642FI Tall Tub Dishwasher
AEG FFE83800PM Dishwasher
CMA DISHMACHINES UC65e M3 Dishwasher
Westinghouse WSF6606 Dishwasher
BOSCH SHX78B75UC Dishwasher
KitchenAid KDPM604KPS Dishwasher
Miele G 7783 SCVi AutoDos K2O FF Dishwasher
FISHER PAYKEL DD24SCTB9_N Dishwasher
BOSCH SMV25BX04R Dishwasher
Whirlpool WH7IPC15BM60 Dishwasher
CMA DISHMACHINES H-1X Undercounter Dishwasher
ASKO DBI565IXXLS Logic Series 24 Dishwasher