BAUKNECHT 295f471f27d55b Dishwasher User Manual
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt
indicator is lit
Salt reservoir is empty (after refill the salt indicator Refill reservoir with salt (for more information - see page 2).
may remain lit for several wash cycles).
Adjust water hardness (see table, page 2).
Rinse aid
indicator is lit
Rinse aid dispenser is empty (after refill the rinse aid
indicator may remain lit for several wash cycles).
Refill dispenser with rinse aid (for more information - see page 2).
Insert the plug into the socket.
The appliance has not been plugged in properly.
Power outage.
For safety reasons, dishwasher will not restart automatically when power returns.
Press the START/Pause button to resume the cycle.
The dishwasher
won’t start or does
not respond to
commands.
The dishwasher door is not closed.
ActiveDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for > 4 seconds. Close the door and press START/Pause button.
It does not respond to commands. Display shows:
Switch off the appliance by pressing the ON/OFF button, switch it back on after
F9 or F12 and both On/Off and START/Pause LEDs approximately one minute and restart the program. If problem persists, unplug the
are blinking rapidly.
appliance for 1 minute, then plug it back in.
The dishwasher
won’t drain.
Display shows: F3
and both On/Off
and START/Pause
LEDs are blinking
rapidly.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes
excessive noise.
The detergent has not been measured out correctly or it is not suitable for use in dish-
washers (see FILLING THE DETERGENT DISPENSER). Restart dishwasher by pressing the
DRAIN button (see OPTIONS AND FUNCTIONS) and run new program without detergent.
An excessive amount of foam has been produced.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hindered
by the dishes.
The wash cycle is too gentle.
The dishes are not
clean.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure there is water in the water supply or the tap running.
The dishwasher
does not fill the wa-
ter. Display shows:
and F6, both
No water in the water supply or the tap is closed.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
The inlet hose is bent.
On/Off and START/
Pause LEDs are
blinking rapidly.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
After having carried out the verification and cleaning, turn off and turn on the dish-
washer and restart a new program.
Dishwasher finishes
the cycle prema-
turely. Display
Drain hose positioned too low or siphoning into
home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
shows: F15 and
both On/Off and
START/Pause LEDs
are blinking rapidly.
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Depends on the liquid detergent used and can be
emphasized in case of Delay option is activated.
Small leaks will not cause machine malfunction and can be avoided by changing
liquid detergent type or using tablets.
Detergent leaks.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.bauknecht.eu and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
8
| General | Details |
|---|---|
| Name | BAUKNECHT 295f471f27d55b Dishwasher |
| Make | Bauknecht |
| Language | English |
| Filetype | PDF (Download) |
| File size | 8.25 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Bauknecht B7I HF60 Dishwasher
Bauknecht BK6UC11BS7A0X Dishwasher
Bauknecht Dishwasher
Bauknecht 3O35 PF Dishwasher
Bauknecht AUTBFC3C26 Dishwasher
BAUKNECHT B2I HD526 A Dishwasher
Bauknecht BFP 5O41 PLT X Dishwasher
KitchenAid KDTF324PPA Dishwasher
BOSCH SMS2HVW66G Dishwasher
FISHER PAYKEL DD24DHTI9 N Sanitize Dishwasher
SIEMENS SX95Z802CE XXL iQ500 Dishwasher
FISHER PAYKEL DD60DDFB9 Double Dishwasher
FISHER PAYKEL DD60STX6I1 Sanitise Integrated Single DishDrawer Dishwasher
ASKO DBI343ID.W.AU Dishwasher
BOSCH SMS4HCI19E Dishwasher
GE APPLIANCES GDF550PGR Plastic Interior Dishwasher with Front Controls
BOSCH 9001164801 Dishwasher