Bauknecht AUTBFC3C26 Dishwasher
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when the RINSE AID REFILL indicator light
in the control
elastic elements from the upper rack.
panel is lit.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
•
•
It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL
A
indicator light
in the control panel is lit.
B
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt
reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the pro-
cedure before the beginning of the washing cycle to avoid corrosion.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can ad-
just the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button P three times - a beep will be heard.
• Switch it on using the ON/OFF button.
SETTING THE WATER HARDNESS
• The current selection level number and rinse aid indicator light flash.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
Setting is complete!
The factory sets the default value for the water hardness.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
If the rinse aid level is set to ZERO, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes, set a
mid-range number (3-4).
•
Hold down button P for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
The current selection level number and the salt indicator light both flash.
•
• Press button P to select the desired hardness level (see WATER
HARDNESS TABLE).
Water Hardness Table
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C.
Introduce the detergent into the dry dispenser D only. Place the
amount of detergent for pre-washing directly inside the tub.
°dH
German degrees
°fH
French degrees
°Clark
English degrees
Level
Soft
1
2
3
4
5
0 - 6
0 - 10
11 - 20
21 - 29
30 - 60
61 - 90
0 - 7
Medium
Average
Hard
7 - 11
8 - 14
1. When measuring out the detergent
refer to the mentioned earlier infor-
mation to add the proper quantity.
Inside the dispenser D there are indi-
12 - 16
17 - 34
35 - 50
15 - 20
21 - 42
43 - 62
D
cations to help the detergent dosing.
2. Remove detergent residues from
the edges of the dispenser and clo-
Very hard
C
• Switch off the appliance by pressing the ON/OFF button.
se the cover until it clicks.
Setting is complete!
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
button, because it adjusts the program so that the best washing and
drying results are always achieved.
After the salt has been poured into the machine, the SALT REFILL indi-
cator light switches off.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result of limescale accumulation.
Using of Salt is recommended with any type of dishwasher deter-
gent.
Usage of detergent not designed for dishwashers may cause mal-
function or damage to the appliance.
2
| General | Details |
|---|---|
| Name | Bauknecht AUTBFC3C26 Dishwasher |
| Make | Bauknecht |
| Language | English |
| Filetype | PDF (Download) |
| File size | 9.36 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Bauknecht B7I HF60 Dishwasher
Bauknecht BK6UC11BS7A0X Dishwasher
BAUKNECHT 295f471f27d55b Dishwasher
Bauknecht Dishwasher
Bauknecht 3O35 PF Dishwasher
BAUKNECHT B2I HD526 A Dishwasher
Bauknecht BFP 5O41 PLT X Dishwasher
MAYTAG W11363089B Dishwasher
BOSCH SMV6ECX10E Dishwasher
Electrolux KEQC7210L Air Dry Dishwasher
IKEA 004.754.23 PROFFSIG Integrated Dishwasher
FISHER PAYKEL DD24DT2NX9 Dishwasher
BOSCH SHP88PZ55N Dishwasher
SIEMENS SN65EX07CE Dishwasher
BOSCH SMV4HCX58E-39 Dishwasher
BOSCH SPV2HKX42G Dishwasher
smeg STL233CLH Universale Totally dishwasher