Bauknecht AUTBFC3C26 Dishwasher
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt reservoir is empty. (After refill the salt indica- Refill reservoir with salt (for more information - see page 2).
Salt
indicator is lit
tor may remain lit for several wash cycles).
Adjust water hardness - see table, page 2.
Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for several wash cycles).
Rinse aid
indicator is lit
Refill dispenser with rinse aid (for more information - see page 2).
The appliance has not been plugged in properly. Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press START/Pause button and close the door within 4 seconds.
Power outage.
The dishwasher
won’t start or does
not respond to
commands.
The dishwasher door is not closed.
ActiveDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for more
than 4 seconds.
Press START/Pause and close the door within 4 seconds.
It does not respond to commands.
Display shows: 9 or 12 and On/Off LED is blin-
king rapidly
Switch off the appliance by pressing the ON/OFF button, switch it back on after approxi-
mately one minute and restart the program. If problem persists, unplug the appliance for
1 minute, then plug it back in.
The wash cycle has not finished yet.
The drain hose is bent.
Wait until the wash cycle finishes.
The dishwasher
won’t drain.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Display shows:
3 and On/Off LED is
blinking rapidly
The sink drain pipe is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The dishwasher
makes excessive
noise.
The detergent has not been measured out correctly or it is not suitable for use in
dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by
switching OFF the dishwasher, then switch it on again, select a new program, press
START/Pause and close the door within 4 seconds. Please do not add any detergent.
An excessive amount of foam has been produced.
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The spray arms cannot rotate freely, being hinde-
red by the dishes.
The wash cycle is too gentle.
The dishes are not
clean.
The detergent has not been measured out correctly or it is not suitable for use in dishwa-
shers (see FILLING THE DETERGENT DISPENSER).
An excessive amount of foam has been produced.
The cap on the rinse aid compartment has not
been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
The dishwasher
does not fill the
water.
Display shows: H,
6 and On/Off LED is
blinking rapidly
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
The inlet hose is bent.
The sieve in the water inlet hose is clogged; it is After having carried out the verification and cleaning, turn off and turn on the dishwa-
necessary to clean it sher and restart a new program.
Dishwasher finishes
the cycle prema-
turely.
Drain hose positioned too low or siphoning into Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
home sewage system.
siphoning into home sewage system, install air admittance valve if necessary.
Display shows: 15
and On/Off LED is
blinking rapidly
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Depends on the liquid detergent used and can be
emphasized in case of Delay option is activated.
Small leaks will not cause machine malfunction and can be avoided by changing liquid
detergent type or using tablets.
Detergent leaks.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.bauknecht.eu and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product‘s identification plate.
IEC 436
:
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
8
| General | Details |
|---|---|
| Name | Bauknecht AUTBFC3C26 Dishwasher |
| Make | Bauknecht |
| Language | English |
| Filetype | PDF (Download) |
| File size | 9.36 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Bauknecht B7I HF60 Dishwasher
Bauknecht BK6UC11BS7A0X Dishwasher
BAUKNECHT 295f471f27d55b Dishwasher
Bauknecht Dishwasher
Bauknecht 3O35 PF Dishwasher
BAUKNECHT B2I HD526 A Dishwasher
Bauknecht BFP 5O41 PLT X Dishwasher
INDeSIT D2F HD624 A Dishwasher
FISHER PAYKEL DD60D2HNB9 Built Under Double Dishwasher
Miele G 15740-45 SCi SL Brilliant Dishwasher
beko BDFN15430G Electrical Household Dishwasher
FISHER PAYKEL DD60SA9 Dishwasher
Haier HDW9TFE3SS2 Compact Dishwasher
FISHER and PAYKEL DD60SHTI9 Tall Dishwasher
FISHER AND PAYKEL DD60D4HNB9 Drawer Dishwasher
BOSCH SPS6ZMI29E Free Standing Dishwasher
Not mentioned WFE 2B19 X UK Dishwasher