Home > CMA Dishmachines > CMA DISHMACHINES UC65e M3 Dishwasher

CMA DISHMACHINES UC65e M3 Dishwasher

Maintenance  
Maintenance - Schedules  
Daily Maintenance  
1.  
2.  
3.  
4.  
5.  
6.  
Check all of the wash arm and rinse arm spray jets and clean as necessary.  
Make sure the water supply is on and the drain is not clogged.  
Check the temperature display and ensure it is operating.  
Make sure the dish racks are in good condition.  
Check the chemical containers and refill as required.  
Follow the cleaning procedures on pg.15.  
Weekly Maintenance  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Perform Steps 1-6 in the Daily Maintenance.  
Inspect water lines for leaks.  
Check for water leaks underneath the dishwasher.  
Make sure the floor drain and/or drain lines are unobstructed.  
Make sure the dishwasher is level.  
Clean accumulated lime deposits from the wash tank heating element.  
Inspect the scrap screen and replace if damaged.  
Check the spray arms and replace or repair if damaged.  
8.  
Semi-Annual Maintenance  
1.  
Inspect the chemical dispensing pump tubing for cuts, kinks or bends and replace if  
necessary.  
2.  
Place an empty dish rack inside the dishwasher. Remove the pick-up tubes from the  
chemical containers. Place the tubes in a container of hot water and run the dishwasher for  
twenty cycles to thoroughly flush the lines. Check the lines to ensure they are unobstructed.  
3.  
4.  
Disassemble the detergent pump and replace the squeeze tube. Reassemble.  
Return the pick-up tubes into full chemical containers and return the machine to service.  
Yearly Maintenance  
Contact your authorized service agent for a preventive maintenance inspection.  
Lubrication  
There are no lubrication points for this dishwasher.  
19  
Maintenance  
Maintenance - Troubleshooting Chart  
Condition  
Cause  
Solution  
Dishwasher will not run.  
Door not closed.  
Main power OFF.  
Dishwasher OFF.  
Close door completely.  
Check breaker on panel.  
Turn dishwasher power switch ON.  
Low or no water.  
Main water supply off.  
Fill hose kinked.  
Open supply valve.  
Straighten fill hose.  
Temperature display  
indicates "LP"  
Low incoming water pressure  
Check for kinked or damaged lines.  
Set flowing water pressure to 20-22 PSI.  
Solenoid valve defective.  
Solenoid strainer clogged.  
Install repair kit or replace.  
Clean strainer.  
Chemicals won’t feed into  
dishwasher.  
Chemical supply low.  
Refill chemical container.  
Replace tubing.  
Supply tubing damaged.  
Supply tubing kinked.  
Straighten tubing.  
Pick-up tube clogged  
Clean/replace tube.  
Squeeze tube or diaphragm bad.  
Replace defective components.  
Clogged scrap screen.  
Clogged spray arms.  
Clean scrap screen.  
Clean spray arms.  
Low water pressure  
pumped from wash spray  
arms.  
Clogged pump intake screen.  
Inspect sump and clean pump intake  
screen.  
Poor wash results.  
Excessively hard water.  
Water temperature low.  
Contact chemical supplier.  
Raise incoming water  
temperature to 140°F  
Thermistor defective.  
Replace thermistor.  
(See chemicals won’t feed  
above.)  
(See chemicals won’t feed  
above.)  
(See low or no water above.)  
Chemical injector defective.  
(See low or no water above.)  
Replace squeeze tube.  
Replace injector motor.  
Clean tubing and pick-up.  
Wares incorrectly loaded.  
in dishrack.  
Reposition wares or reduce amount of  
wares in dish racks.  
Booster high limit tripped.  
Reset or replace high limit.  
Reset or replace high limit.  
Wash tank high limit tripped.  
Delime the rinse arms and clean the  
rinse jets with paper clip.  
Rinse jets clogged  
Water has drained out of  
the wash tank while the  
dishwasher was idle.  
Anti-siphon loop in drain  
hose has been removed.  
Re-route drain hose.  
DO NOT STRETCH HOSE  
Drain hose clamp is not  
holding the drain hose  
in proper position.  
Replace/adjust hose clamp  
making sure goose-neck  
is maintained.  
Building plumbing does not  
provide correct air vent  
to prevent siphoning.  
Contact service Agent  
and/or plumber.  
WAIT light is on for an  
extended period of time.  
Incoming water supply cold  
Raise incoming water temperature.  
Replace final rinse booster thermistor.  
Rinse Sentry extends wash mode  
for a maximum time of 5-minutes  
to allow final rinse water booster  
Dishwasher stays in  
wash cycle for an  
extended period of time..  
20  
GeneralDetails
NameCMA DISHMACHINES UC65e M3 Dishwasher
MakeCMA Dishmachines
LanguageEnglish
FiletypePDF (Download)
File size1.49 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
CMA DISHMACHINES EST-44 Conveyor Dishwasher
CMA DISHMACHINES EST-44 Conveyor Dishwasher
CMA DISHMACHINES CMA-180UC Under Counter Dishwasher
CMA DISHMACHINES CMA-180UC Under Counter Dishwasher
CMA DISHMACHINES EST-AH Door Type Rack Low Dishwasher
CMA DISHMACHINES EST-AH Door Type Rack Low Dishwasher
CMA DISHMACHINES CMA-180VL Dishwasher
CMA DISHMACHINES CMA-180VL Dishwasher
CMA DISHMACHINES UC50e Dishwasher
CMA DISHMACHINES UC50e Dishwasher
CMA DISHMACHINES CMA-180 Dishwasher
CMA DISHMACHINES CMA-180 Dishwasher
CMA DISHMACHINES CMA-180UC Dishwasher
CMA DISHMACHINES CMA-180UC Dishwasher
CMA DISHMACHINES H-1X Undercounter Dishwasher
CMA DISHMACHINES H-1X Undercounter Dishwasher
CMA DISHMACHINES 180UC-3 Under Counter Dishwasher
CMA DISHMACHINES 180UC-3 Under Counter Dishwasher
CMA DISHMACHINES AH Straight Thru Design Dishwasher
CMA DISHMACHINES AH Straight Thru Design Dishwasher

CMA DISHMACHINES UC65e M3 Dishwasher