FAGOR AD-120CW Door Style Dishwasher
TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
ACTION
Dishwasher will NOT FILL
after the door is closed.
Power “ON” light (L1) is not
illuminated.
Service breaker tripped
Reset. If the breaker trips again, contact an electrician to
verify amps or possible short.
Machine not connected to
Verify the unit is connected to a hot (live) feed. Verify
voltage and proper phasing.
power source.
Faulty Circuit Board
Make sure power is being supplied to the board. Check
for loose wiring harness connections. Check circuit board
fuse. Check voltage between R (brown) and N (blue). If
208V-240V found, replace circuit board.
No water to machine
Machine not level
Verify hose is not blocked or kinked, water valve is open
and pressure > 20 psi.
Level machine. Legs are height adjustable.
Overflow tube not attached
or broken / missing O-ring.
Faulty door switch
Check condition of overflow tube. Make sure O-ring is in
good working condition and in place.
Dishwasher will NOT FILL
or reach the appropriate
water level after the door is
closed. Power “ON” light (L1)
is illuminated.
Verify the wiring at the switch for loose connections; if
no loose connections are present, replace the switch (Ip)
or the door relay (Cp)
Faulty fill pressure switch
(P1)
Verify voltage at terminal 2 (brown) and GND. If no
voltage, P1 is possible stuck.
Faulty rinse/ fill valve (V)
Verify the wiring and proper voltage at valve; if correct
replace fill valve.
Faulty fill pressure switch
(P1)
Verify it changes position of the switch; on terminal 1 to
2 (fill), and 1 to 3 (heating) If not replace it.
Faulty Power/ Start button
(St)
Verify good connection between digital start buttons and
circuit board. If disconnected, reconnect and verify.
Verify circuit board fuse is If connected and still not
working, replace Adhesive Trim.
Dishwasher will NOT RUN
after the door is closed.
Power “ON” light (L1) is
illuminated and the unit has
completed the filling and
heating cycle.
Make sure power is being supplied to the board. Check
for loose wiring harness connections. Check circuit board
fuse. Check voltage between R (brown) and N (blue). If
208V-240V found, replace circuit board.
Faulty Circuit board
Faulty wash pump (MBL)
Rotate the pump from the shaft flat head slot counter-
clock wise to verify free rotation. Verify that the wash
pump is getting power. If so, replace the pump.
Faulty start buttons
Verify good connection between digital start buttons and
circuit board. If disconnected, reconnect and verify.
Verify circuit board fuse is If connected and still not
working, replace Adhesive Trim.
Rinsing temperature gauge
is lower than 180º F.
Wait until sanitized rinsing temperature reached a min.of
180º F. Check out your incoming water temperature.
Recommended incoming water temperature is 140°F
P. 15
| General | Details |
|---|---|
| Name | FAGOR AD-120CW Door Style Dishwasher |
| Make | FAGOR |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.72 MB |
(1 votes, average: 5.00 out of 5)
Loading...
FAGOR 3LVF-421.1, 3LVF-421.1X Dishwasher
FAGOR 3LVF-423.1X Dishwasher
FISHER AND PAYKEL DW60UN2B2 Built Under Dishwasher
BOSCH SRV2HKX39G Dishwasher
Miele PFD 101 U Built Under Dishwasher
Whirlpool WDFS3L5PIXAU Power Clean Maxi Tub 15 Place Setting Dishwasher
AMANA ADB1400AMS Undercounter Dishwasher
FISHER PAYKEL DD24ST4NX9 Dishwasher
kleenmaid DW6020X Dishwasher
ARDESTO DWMF-V608SMHDS Dishwasher
CMA DISHMACHINES CMA-180UC Under Counter Dishwasher
BOSCH SMH8ZB802E Dishwasher