Gaggenau 9001923390_A Free Standing Dishwasher
Dishwasher Connectionꢀen-us
6. To cover the screw heads, use the black plastic caps.
¡ Always use appropriate seals when making plumbing
connections.
1. Flush the incoming water line for approximately 1
minute to clear any foreign material.
2. Connect the dishwasher water supply line to the water
shut off valve, using the adaptor if included with your
model.
‒ Install a shut off valve if one isn’t already in the
supply line.
‒ Make sure there are no sharp bends or kinks in the
water line that might restrict water flow.
D
h
nec
5ꢀDishwasher Connection
D
h
nec
Follow these instructions to connect the dishwasher.
5.1ꢀInstalling the Water Inlet Connection
The hot water heater should be set to deliver
approximately 120 °F (49 °C) [max. 140 °F/ (60 °C)]
water to the dishwasher. Water that is too hot can cause
some detergents to lose effectiveness. Lower water
temperatures will increase run times. The hot water supply
pressure must be between 7.25 - 145 psi (0.5 - 10 bar).
3. Properly tighten all water connections.
4. After all connections are made, turn on the hot water
and check for leaks.
WARNING
Scalding Hazard
5.2ꢀInstalling the Drain Connection
▶ Do not perform any work on a pressured hot water line.
Serious injury could result. Only qualified plumbers
should perform plumbing work. Do not attempt any work
on the dishwasher hot water supply plumbing until you
are certain the hot water supply is shut off.
The drain hose must be installed with either a high loop or
an air gap.
NOTICE:
Proper drain hose installation
▶ The dishwasher drain hose must be installed with a
portion of it at least 33” (84 cm) off the floor; otherwise
the dishwasher may not drain properly.
Remove garbage disposal plug
▶ If the dishwasher drain hose will be connected to a
garbage disposal connection, first remove the plug from
the disposal connection.
NOTICE:
Soldering plumbing lines
▶ Temperatures required for soldering and sweating will
damage the dishwasher. If plumbing lines are to be
soldered or sweated, keep the heat source at least 6
inches (152.4 mm) away from the dishwasher.
Plumbing codes
▶ Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
Note
Important notes for drain connection:
¡ If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
Note
¡ The drain hose length can be extended if necessary.
Use kit #SGZ1010UC. The maximum length of the drain
hose, including the hose leading to the air gap, is 150″
(380 cm).
¡ You may attach the hose clip to the inside of the
adjacent cabinet to hang the drain hose (screws are not
supplied) in place of using a nonmetallic tie as pictured
in the next illustrations. Do not exceed 43” in drain hose
height.
Important notes for water connection:
¡ If using a solder joint instead of a compression fitting,
be sure to complete all solder connections before
connecting the water supply line to the dishwasher.
¡ Use an approved dishwasher water supply line with the
correct fittings for this connection.
¡ If using copper tubing or other material not depicted in
this manual for water supply, defer to a licensed
plumber for proper installation.
13
| General | Details |
|---|---|
| Name | Gaggenau 9001923390_A Free Standing Dishwasher |
| Make | Gaggenau |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.58 MB |

Gaggenau DF264101 Dishwasher

GAGGENAU DF271101F Dishwasher

GAGGENAU DF481100 Dishwasher

GAGGENAU 400 Dishwasher

GAGGENAU DF480161F Dishwasher

Gaggenau 9001923384 B Dishwasher

GAGGENAU DF261101 Dishwasher

Gaggenau DF211700 Dishwasher

GAGGENAU DF480701F Dishwasher

GAGGENAU DF481100F 400 Series Dishwasher













































