Hotpoint H8I HP42 Dishwasher
Daily Reference Guide
EN
The lower spray arm may be removed
by pulling it upwards and rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it down and
rotating it clockwise.
CLEANING THE SPRAY ARMS
On occasions, food residue
may become encrusted onto
the spray arms and block the
holes used to spray the water.
It is therefore recommen-
ded that you check the arms
from time to time and clean
them with a small non-me-
tallic brush.
The top spray arm may be removed
by pressing it up and then rotating it
anti-clockwise. Mounting back the
spray arm is by pulling it upwards and
rotating it clockwise.
To remove the upper spray
you must remove it together
with the manifold.
The Top Rack rack has a fixed wash tube with all the wash nozzles facing
upward. To clean it you can slide the rack out and with a tweezer remove
items that may be lodged in the nozzles.
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service whose contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
SOLUTIONS
Salt
Refill the reservoir with salt (for more information - see FILLING THE SALT RESERVOIR). Check the
water hardness setting if necessary (see SETTING THE WATER HARDNESS)
Salt reservoir is almost empty.
indicator is lit
Salt indicator is
Salt reservoir is empty.
blinking
Refill the reservoir with salt as soon as possible. Using the appliance without salt may cause
damage to its internal components.
Rinse aid
indicator is lit
or blinking
Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for a short time).
Refill the dispenser with a rinse aid (for more information - see FILLING THE RINSE AID DISPENSER).
Descale indicator
is lit or blinking;
"dES" alarm is displayed.
Descale the appliance immediately using the Self-Clean program and a commercially available
descaling product (see OPTIONS AND FUNCTIONS). Refill the reservoir with salt. Check the water
hardness setting. If the appliance is not descaled, it will stop functioning.
Limescale is accumulating on internal components
of the appliance
The appliance has not been plugged in properly. Insert the plug into the socket.
For safety reasons, dishwasher will not re-start automatically when power returns.
Open dishwasher door, press START/Pause button and close the door within 4 seconds.
Power outage.
The dishwasher
won’t start or does
not respond to com-
mands.
The dishwasher door is not closed.
ActiveDry pin is not pulled in.
Vigorously push the door until you hear the “click”.
Cycle is interrupted by door opening for more
than 4 seconds.
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON-OFF/Reset, switch it back on after approximately one
minute and restart the program. If problem persists, unplug the appliance for 1 minute, then plug
it back in.
Control panel does not respond or F6 E1
is displayed.
Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY and DESCALE IN-
STRUCTION).
Filter is clogged with food residues or limescale
Dishwasher
won’t drain.
Display shows:
F7 E3 or F9 E1
Drain hose is kinked.
Check the drain hose (see INSTALLATION INSTRUCTION).
Clean the sink drain pipe.
Sink drain pipe is blocked.
Dishes are rattling against each other.
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for use in dishwashers
(see FILLING THE DETERGENT DISPENSER). Restart the current cycle by switching OFF the dishwa-
sher, then switch it on again, select a new program, press START/Pause and close the door within
4 seconds. Please do not add any detergent.
Excessive amount of foam is present.
Dishwasher makes
excessive noise.
Crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
Filter is clogged with food residues or limescale Clean the filter assembly (see CARE AND MAINTENANCE).
Crockery has not been arranged properly. Arrange the crockery correctly (see LOADING THE RACKS).
Spray arms cannot rotate freely, being hindered Arrange the crockery correctly (see LOADING THE RACKS). Check that the upper rack is in correct
by the dishes.
position and adjust (lift up) if necessary
Wash cycle is too gentle.
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see
FILLING THE DETERGENT DISPENSER).
Excessive amount of foam is present.
Dishes are not clean.
Cap on the rinse aid compartment has not been
closed correctly.
Make sure the cap of the rinse aid dispenser is closed.
Filter is clogged with food residues or limescale Clean the filter and descale the appliance (see CLEANING THE FILTER ASSEMBLY).
Salt reservoir is empty. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
5
| General | Details |
|---|---|
| Name | Hotpoint H8I HP42 Dishwasher |
| Make | Hotpoint |
| Language | English |
| Filetype | PDF (Download) |
| File size | 9.15 MB |
(1 votes, average: 5.00 out of 5)
Loading...
Hotpoint H7I HP42 L UK Dishwasher
Hotpoint H7F HP33 UK Dishwasher
Hotpoint H7F HS41 UK Full Size Dishwasher
Hotpoint H8I HT59 LS UK Dishwasher
Hotpoint H7F HS51 Dishwasher
Hotpoint H7FHS41 Dishwasher
Hotpoint HA3FC10BS7A0S Dishwasher
Hotpoint H7F HS41 X Dishwasher
Hotpoint 869991662940 Dishwasher
Hotpoint H7I HT59 L Dishwasher
TOSHIBA DW-15F5SS-AU Dishwasher
Westinghouse WSF6608XB Dishwasher
JennAir Dishwasher
Electrolux KESC7325L Dishwasher
FISHER PAYKEL DD60ST4NX9 Single DishDrawer Dishwasher
SIEMENS SE61HX02AG Dishwasher
Whirlpool WDP370PAHB Dishwasher
Whirlpool WDF110PAB Undercounter Dishwasher
FOTILE BD3B-G6 Dishwasher
SIEMENS SN13ES78CS Dishwasher