IKEA FINPUTSAD Integrated Dishwasher
ENGLISH
17
Installation
ATTENTION: If the appliance must be moved at any time, keep
it in an upright position; if absolutely necessary, it may be tilted
onto its back.
Electrical connection
WARNING: Under no circumstances should the water inlet
hose be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure
that:
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the
appliance as shown on the data plate located on the inside of
the door (see PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised service only to replace
the certified power cord with a correct plug dedicated for this
appliance (see AFTER-SALES SERVICE). Do not use extension
cablesor multiple sockets or not authorized power cords with
plugs. Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the
manufacturer or its authorised Technical Assistance Service in
order to prevent all potential hazards.
Connecting the water supply
Adaptation of the water supply for installation should only be
performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards the
right or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
Connecting the water inlet hose
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or
an authorised technician.
The water pressure must be within the values indicated in the
Technical Data table - otherwise the dishwasher may be function
properly.
Make sure the hose is not bent or compressed.
Specifications for the connection of the water supply hose:
Water supply
Water intake
cold or hot (max. 60°C)
The Company shall not be held responsible for any incidents, if
these regulations are not observed.
3/4”
0.05 ÷ 1 MPa (0.5 ÷ 10 bar)
7.25 – 145 psi
Positioning and levelling
Power of water pressure
1. Position the dishwasher on a level sturdy floor. If the floor is
uneven, the front feet of the appliance may be adjusted until
it reaches a horizontal position. If the appliance is levelled
correctly, it will be more stable and much less likely to move
or cause vibrations and noise while it is operating.
Connecting the water outlet hose
Connect the outlet hose to a drain duct with a minimum
diameter of 2 cm A.
2. Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any
condensation which may form.
MAX 80 cm
3. Place the dishwasher so that its sides or back panel are in
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop.
MIN 40 cm
4. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the
dishwasher using a hexagonal spanner with an opening of 8
mm. Turn the spanner in a clockwise direction to increase the
height and in an anticlockwise direction to decrease it.
The outlet hose connection must be at a height ranging from
40 to 80 cm from the floor or surface where the dishwasher
rests. Before connecting the water outlet hose to the sink drain,
remove the plastic plug B.
DIMENSIONS AND CAPACITY:
Width
448 mm
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occur, the
dishwasher is provided with a special system which blocks the
water supply in the event of anomalies or leaks from inside the
appliance.
The dishwasher is also equipped with the supplementary
safety device New Aqua Stop, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it
contains live electrical parts.
Height
Depth
820 mm
555 mm
Capacity
10 standard place-settings
| General | Details |
|---|---|
| Name | IKEA FINPUTSAD Integrated Dishwasher |
| Make | Ikea |
| Language | English |
| Filetype | PDF (Download) |
| File size | 3.64 MB |
(1 votes, average: 5.00 out of 5)
Loading...
IKEA 404.755.53 Medelstor Dishwasher
IKEA 804.621.67 Lagan Dishwasher
IKEA RENGÖRA 204.756.05 Dishwasher
IKEA 9001774317 TORSBODA Dishwasher
IKEA 9001774318 Dishwasher
IKEA SBE8596Z0E DISKAD PROFFSIG Dishwasher
IKEA VILLBODA Dishwasher
IKEA 504.754.25 HYGIENISK Dishwasher
IKEA AA-2412057-2-1 RÅGLANDA Dishwasher
IKEA 905.681.49 OSTVEDA Dishwasher
BOSCH SBT4ECX10E Integrated Dishwasher
FISHER PAYKEL DW60FC1X1 Dishwasher
Miele PFD 101 Dishwasher
SIEMENS SN23EI14AE Dishwasher 60 cm A+++
FISHER PAYKEL DD24SI9N Dishwasher
IKEA RÅGLANDA Integrated Dishwasher
ILVE IVFID10 Dishwasher
BOSCH SMV2ITX48E Dishwasher
BOSCH SBD6ECX00E Dishwasher
FISHER PAYKEL DW60U6I1 Sanitise Integrated Dishwasher