InDesiT D2I HD526 Dishwasher
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
Please scan the QR code on your product in order to have more detailed information.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
DELAY -The start of the program may be delayed for a period of time
between 1 and 12 hours.
The DELAY function cannot be set once a wash cycle has been started.
PUSH&GO - Push&GO button is an easily distinguishable button that
allows you direct access to the Push&GO program, a wash and dry cycle
that ensures great cleaning performance in a short time.You don’t have to worry
which program to choose, Push&GO cycle will do the work for you.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
CAPACITY: 14 standard place-settings
LOADING THE RACKS
UPPER RACK
CUTLERY BASKET
The basket is equipped with top grilles for improved cutlery arrangement.
The cutlery basket should be positioned only at the front of the lower rack.
LOWER RACK
FOLDABLE
FLAPS
WITH AD-
JUSTABLE
POSITION
(loading example for the
lower rack)
(loading example for the
upper rack)
For pots, lids, plates, salad
bowls, cutlery etc.. Large
plates and lids should ide-
ally be placed at the sides
to avoid interferences with
the spray arm.
Load delicate and light
dishes: glasses, cups, saucers,
low salad bowls.
Knives and other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards or they must be po-
sitioned horizontally in the tip-up compartments on the upper rack.
More information in the Daily Reference Guide on website.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
3
1
2
4
B
A
A
C
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
The lower spray arm may
be removed by pulling it
upwards.
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
Please scan the QR code on your product in order to have more detailed information.
TROUBLESHOOTING
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The dishwasher does not
fill the water.
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
Display shows: H,
6 and On/Off LED is
blinking rapidly
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and
reboot.
The inlet hose is bent.
The sieve in the water inlet hose is clogged; it is After having carried out the verification and cleaning, turn off and turn on the dishwasher
necessary to clean it and restart a new program.
Dishwasher finishes the
cycle prematurely.
Drain hose positioned too low or siphoning into Check if end of drain hose is placed at correct height (see INSTALLATION).Check for sipho-
home sewage system.
ning into home sewage system, install air admittance valve if necessary.
Display shows: 15 and On/
Off LED is blinking rapidly
Air in water supply.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.indesit.eu and parts-selfservice.whirlpool.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-
sales Service, please state the codes provided on your product‘s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
IEC 436
:
400011658929B
2
01/2023 dk - Xerox Fabriano
| General | Details |
|---|---|
| Name | InDesiT D2I HD526 Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 1.51 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
Indesit I0F D641A Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
Westinghouse WSU6608XB Dishwasher
BERTAZZONI DW24S2IPB Dishwasher
Bosch SMU8ZCS01A Dishwasher
BOSCH SPS4HMW61E Dishwasher
BOSCH SPH4HL801E Fully Integrated Dishwasher
BOSCH SPI4HMS49E Dishwasher
Fisher and Paykel DW60FC6X1 Dishwasher
COVE DW2450, DW2450WS Dishwasher
FOTILE BD2B-G2-Y Matte Glass Dishwasher
Whirlpool WDFS3R4NWESG Sense Dishwasher