Indesit I0F D641A Dishwasher
EN
Quick Guide
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@europeanappliances.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
Please scan the QR code on your product in order to have more detailed information.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE - If there are not many dishes to be washed, a half load-
ing may be used in order to save water, electricity and detergent.
By default the appliance washes dishes in all racks.
DELAY -The start of the program may be delayed for a period of time
between 0:30 and 24 hours
The DELAY function cannot be set once a wash cycle has been started.
TABLET (Tab) - If you use powder or liquid detergent, this option
Auto Door is a convection drying system which automatically opens
the door during/after drying phase to ensure exceptional drying
performance every day. Door opens at the temperature that is safe to
your kitchen furniture.
should be off.
PUSH&GO - button is an easily distinguishable button that allows you
direct access to the Push&GO program, a wash and dry cycle that en-
sures great cleaning performance in a short time. You don’t have to worry
which program to choose, Push&GO cycle will do the work for you.
CAPACITY: 14 standard place-settings
LOADING THE RACKS
FOLDABLE
CUTLERY RACK
UPPER RACK
LOWER RACK
FLAPS WITH
ADJUSTABLE
POSITION
For pots, lids, plates, salad bowls,
cutlery etc. Large plates and lids
should ideally be placed at the
sides to avoid interferences with
the spray arm.
The lower rack has tip-up supports
which can be used in a vertical
position when arranging plates or
in a horizontal position (lower) to
load pans and salad bowls easily.
(loading example for the cutlery
rack)
The third rack was designed to
house the cutlery.
(loading example for the
upper rack)
Load delicate and light dishes: glass-
es, cups, saucers, low salad bowls.
(loading example for the
lower rack)
More information in the Daily Reference Guide on website.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
B
A
A
C
To remove the upper spray arm, The lower spray arm may
turn the plastic locking ring in a be removed by pulling it
clockwise direction.
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.)
please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
upwards.
Please scan the QR code on your product in order to have more detailed information.
TROUBLESHOOTING
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
The dishwasher does not fill
the water. Display shows:
and F6, both On/Off and
START/Pause LEDs are blink-
ing rapidly.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
The inlet hose is bent.
and reboot.
The sieve in the water inlet hose is clogged; it is After having carried out the verification and cleaning, turn off and turn on the dish-
necessary to clean it.
washer and restart a new program.
Dishwasher finishes the cycle
prematurely.
Display shows: F15 and both
On/Off and START/Pause LEDs
are blinking rapidly.
Drain hose positioned too low or siphoning into Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
home sewage system.
Air in water supply.
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
•
•
•
Using QR code on your product.
Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com
Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product’s identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
IEC 436
:
2
| General | Details |
|---|---|
| Name | Indesit I0F D641A Dishwasher |
| Make | INDESIT |
| Language | English |
| Filetype | PDF (Download) |
| File size | 6.68 MB |
(1 votes, average: 5.00 out of 5)
Loading...
INDESIT D2I HL326 Full Size Dishwasher
Indesit D2F HD624 A Separate Dishwasher
Indesit 869991713220 Dishwasher
INDESIT I0F D641A X Free Standing Dishwasher
INDESIT DFE 1B19 14 Dishwasher
INDeSIT D2F Dishwasher
INDeSIT D2I HD524 A Dishwasher
INDESIT W11667630 B Dishwasher
InDeSIT IN2FE10CS90S Dishwasher
inDeSIT DSIO3M24CS Dishwasher
FISHER and PAYKEL DD24ST4NX9 Contemporary Tall Dishwasher
Electrolux ESS87300UX Dishwasher
eta 238290000C Dishwasher
BOSH SBH4HVX00E Dishwasher
smeg LVS344PM 60 cm Free Standing Dishwasher
JENN-AIR JDAF5924RM Dishwasher
FISHER AND PAYKEL DD60SCTX9 7 Contemporary Tall Dishwasher
SIEMENS SN23HW60CE Dishwasher
Electrolux ESM48311SX Free Standing Dishwasher
Kenmore 665.15822000 Undercounter Dishwasher