Home > PHILCO > PHILCO PD 1466 CBIT Dishwasher

PHILCO PD 1466 CBIT Dishwasher

Rinse Aid  
If the “ ”indicator is lit, it means the dishwasher is low on dishwasher  
rinse aid and requires a refill.  
ꢆ Warning indicator  
Salt  
If the “ ”indicator is lit, it means the dishwasher is low on dishwasher  
salt and needs to be refilled.  
Water Softener  
The water softener must be set manually, using the water hardness dial.  
The water softener is designed to remove minerals and salts from the water, which would have a detrimental  
or adverse effect on the operation of the appliance.  
The more minerals there are, the harder your water is.  
The softener should be adjusted according to the hardness of the water in your area.  
Your local Water Authority can advise you on the hardness of the water in your area.  
Adjusting salt consumption  
The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness  
of the water used. This is intended to optimise and customise the level of salt consumption.  
Please follow the steps below for adjustment in salt consumption.  
1. Openthe door, switch on the appliance.  
2. Within 60 seconds after the appliance was switched on press the Program button for more than 5  
seconds to enter the water softener setting mode.  
3. Press the Program button again to select the proper set according to your local environment, the setting  
will change in the following sequence: H1->H2->H3->H4->H5->H6.  
4. Press the Power button to end the setting mode.  
WATER HARDNESS  
Regeneration  
occurs every  
X program  
Salt  
consumption  
(gram/cycle)  
Water softner  
level  
German  
°dH  
British  
French °fH  
Mmol/l  
sequence 1)  
°Clarke  
0 - 5  
0 - 9  
0 - 6  
0 - 0.94  
1.0 - 2.0  
2.1 - 3.0  
3.1 - 4.0  
4.1 - 6.0  
6.1 - 9.8  
H1  
H2  
H3  
H4  
H5  
H6  
No regeneration  
0
6 - 11  
10 - 20  
21 - 30  
31 - 40  
41 - 60  
61 - 98  
7 - 14  
10  
5
9
12 - 17  
18 - 22  
23 - 34  
35 - 55  
15 - 21  
22 - 28  
29 - 42  
43 - 69  
12  
20  
30  
60  
3
2
1
1°dH = 1.25 °Clarke = 1.78 °fH = 0.178 mmol/l  
The factory setting: H3  
1)  
Every cycle with a regeneration operation consumes additional 2.0 litres of water, the energy  
consumption increases by 0.02 kWh and the program extents by 4 minutes.  
EN - 17  
Copyright © 2023, Fast ČR, a. s.  
Revision 05/2023  
GeneralDetails
NamePHILCO PD 1466 CBIT Dishwasher
MakePHILCO
LanguageEnglish
FiletypePDF (Download)
File size4.69 MB
Download PDF
1 Star2 Stars3 Stars4 Stars5 Stars (1 votes, average: 5.00 out of 5)
Loading...
PHILCO PD 1045 EA Dishwasher
PHILCO PD 1045 EA Dishwasher

PHILCO PD 1466 CBIT Dishwasher