SHARP SDW6888JS Slide in Smart Dishwasher
INSTALLATION INSTRUCTIONS
CABINET PREPARATION & WIRE ROUTING
• The wiring may enter the opening from either side, rear or the
PREPARE ELECTRICAL WIRING
WARNING
floor within the shaded area.
FOR PERSONAL SAFETY: Remove house fuse or
open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with
this appliance.
1
• Cut a 1 /2" maximum diameter hole to allow the electrical cable.
The hole must be free of sharp edges. If the cabinet wall is metal,
the hole edge must be covered with a bushing.
• Cable direct connections may pass through the same hole as the
drain hose and hot water line, if convenient. If cabinet wall is
metal, the hole edge must be covered with a bushing.
To ensure electrical safety, installation of an Earth
Leakage Circuit Breaker (ELCB) is recommended to
prevent electrical shocks and other electrical hazards
NOTE: Power cords with plug must pass through a separate hole.
ELECTRICAL CONNECTION TO DISHWASHER
Electrical connection is on the right front of dishwasher.
ELECTRICAL REQUIREMENTS
• This appliance must be supplied with 120V, 60 Hz. It must be
connected to an individual properly grounded branch circuit and
protected by a 15 or 20 ampere circuit breaker or time delay fuse.
• For cable direct connections, the cable must be routed as shown in
Figure E. Cable must extend a minimum of 24" from the rear wall.
• For power cord connections, install a 3-prong grounding type
receptacle. The power supply receptacle for the appliance shall
be installed in a cabinet or on a wall adjacent to the under counter
space in which the appliance is to be installed.
• Wiring must be 2-wire with ground.
• If the electrical supply does not meet the above requirements,
call a licensed electrician before proceeding.
GROUNDING INSTRUCTIONS – CABLE DIRECT
PREPARE HOT WATER LINE
• The line may enter from either side, rear or floor within the shaded
This appliance must be connected to a grounded metal, permanent
wiring system, or an equipment grounding conductor must be run
with the circuit conductors and be connected to the equipment
grounding terminal or lead on the appliance.
area shown in Figure F.
• The line may pass through the same hole as the electrical cable
1
and drain hose. Or, cut an additional 1 /2" diameter hole to
accommodate the water line. If a power cord with plug is used,
water line must not pass through power cord hole.
GROUNDING INSTRUCTIONS – POWER CORD
MODELS
This appliance must be grounded. In the event of a malfunction
or breakdown, grounding will reduce the risk of electric shock by
providing a path of least resistance for electric current. The plug must
be plugged into an appropriate outlet that is installed and grounded
in accordance with local codes and ordinances.
WARNING
Shut-off
Valve
The improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if
there is doubt that the appliance is properly grounded.
Hot
1
1
5ꢀ /3" - 7ꢀ /3"
From Cabinet
18" From Wall
3" From Floor
Cabinet Face
1
1
/2" Dia.
Hole (Max.)
1
1
2
/2" - 3 /2"
From
Cabinet
Power
Cable
24"
From Wall
1
1
Water
Supply
Line
2ꢀ /2" - 3ꢀ /2"
1
1
5ꢀ /3" - 7ꢀ /3"
Ground
Black
White
FIGURE E
4
| General | Details |
|---|---|
| Name | SHARP SDW6888JS Slide in Smart Dishwasher |
| Make | Sharp |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.79 MB |

SHARP SDW6506JS 24 Front Dishwasher

SHARP SDW6888JS Smart Dishwasher

SHARP QW-NA1BF47EI-EU Series Dishwasher

SHARP QW-NA24S42DI-EE Dishwasher

SHARP SDW6767HS Dishwasher

SHARP SDW6767HS Slide In Smart Dishwasher

SHARP SDW6767HS Smart Dishwasher

SHARP QW-NA26F39DI-EN Dishwasher

SHARP QW-NS1CF49EI-ES Dishwasher

SHARP SDW6757ES Dishwasher

























